KORG Triton Studio - Manual (Page 201)

190
a: Wah
The Wah parameter switches the wah effect on/off.
a: Sw
This parameter sets how the wah effect is switched on and off via
the modulation source.
When “Sw” = Moment, the wah effect is usually turned off. It is
turned on only when you press the pedal or operate the joystick.
When a value for the modulation source is less than 64,
“off” speed is selected, and when the value is 64 or higher,
“on” is selected.
When “Sw” = Toggle, the wah effect is switched between on and
off each time you press the pedal or operate the joystick.
The switch will be turned on/off each time the value of the
modulation source exceeds 64.
b: Wah Sweep Range, b: Wah Sweep Src
This parameter sets the sweep range of the wah center frequency.
A negative value will reverse the direction of sweep. The wah cen-
ter frequency can be controlled by the modulation source speci-
fied in the “Wah Sweep Src” parameter.
d: Drive, e: Output Level
The degree of distortion is determined by the level of input signal
and the setting of “Drive”. Raising the “Drive” setting will cause
the entire volume level to increase. Use the “Output Level”
parameter to adjust the volume level. The “Output Level” param-
eter uses the signal level input to the 3-Band EQ. If clipping occurs
at the 3-Band EQ, adjust the “Output Level” parameter.
d: Pre Low-cut
Cutting the signal in the low range before it is input to the Distor-
tion will create a sharp distortion.
g: Q, h: Q
These parameters set the bandwidth of each equalizer. The higher
the value, the narrower the band becomes.
007: St. Parametric 4EQ
(Stereo Parametric 4-Band EQ)
This is a stereo 4-band parametric equalizer. You can select
peaking type or shelving type for Band 1 and 4. The gain of
Band 2 can be controlled by dynamic modulation.
b: Band1 Type, c: Band4 Type
Selects a filter type for Band 1 and 4.
e
Output Level
Sets the output level 0...50
☞
,
Src Off...Tempo
Selects the modulation source for the output level
Amt
Sets the modulation amount of the output level –50...+50
f
Low Cutoff [Hz] 20...1.0kHz
Sets the center frequency for Low EQ (shelving type)
Gain [dB]
Sets the gain of Low EQ –18...+18dB
g
Mid1 Cutoff [Hz] 300...10.00kHz
Sets the center frequency for Mid/High EQ 1 (peaking type)
Q
Sets the band width of Mid/High EQ 1 0.5...10.0
☞
Gain [dB]
Sets the gain of Mid/High EQ 1 –18...+18dB
h
Mid2 Cutoff [Hz] 500...20.00kHz
Sets the center frequency for Mid/High EQ 2 (peaking type)
Q
Sets the band width of Mid/High EQ 2 0.5...10.0
☞
Gain [dB]
Sets the gain of Mid/High EQ 2 –18...+18dB
i
Direct Mix 0...50
Sets the amount of the dry sound mixed to the distortion
Speaker Simulation
Switches the speaker simulation on/off Off, On
j
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance –100...+100
a
Trim
Sets the input level 0...100
b
Band1 Type Peaking, Shelving-Low
Selects the type of Band 1
☞
c
Band4 Type Peaking, Shelving-High
Selects the type of Band 4
☞
d
Band2 Dynamic Gain Src
Selects the modulation source of the Band 2 gain Off...Tempo
☞
Amt [dB]
Sets the modulation amount of Band 2 gain –18...+18dB
☞
e
Band1 Cutoff [Hz]
Sets the center frequency of Band 1 20...1.00kHz
Q
Sets the bandwidth of Band 1 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 1 –18.0...+18.0dB
f
Band2 Cutoff [Hz]
Sets the center frequency of Band 2 50...10.00kHz
Q
Sets the bandwidth of Band 2 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 2 –18.0...+18.0dB
☞
,
g
Band3 Cutoff [Hz]
Sets the center frequency of Band 3 300...10.00kHz
Q
Sets the bandwidth of Band 3 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 3 –18.0...+18.0dB
h
Band4 Cutoff [Hz]
Sets the center frequency of Band 4 500...20.00kHz
Q
Sets the bandwidth of Band 4 0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 4 –18.0...+18.0dB
i
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance –100...+100
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Band1 Band2 Band3 Band4
PEQ PEQ PEQ PEQ
LEQ
LEQ
HEQ
HEQ
PEQ PEQ PEQ PEQ
Trim
Trim
D -mod
3dB
3dB
Band1 Cutoff Band4 Cutoff
0dB
+Gain
–Gain Band1 Type=Peaking
Band1 Type=Shelving Low
Band4 Type=Peaking
Band4 Type=Shelving High
Parametric 4EQ - Band1, Band4 Type