KORG Triton Studio - Manual (Page 225)

214
a: Control Target
This parameter selects no level control, delay output control
(effect balance), or feedback amount control.
a: Polarity, b: Threshold, b: Offset, c: Attack, d: Release
The “Offset” parameter specifies the value for the “Control Tar-
get” parameter (that is set to None), expressed as the ratio relative
to the parameter value (the “Wet/Dry” value with “Control Tar-
get”=Out, or the “Feedback” value with “Control Target”=FB).
When “Polarity” is positive, the “Control Target” value is
obtained by multiplying the parameter value by the “Offset”
value (if the input level is below the threshold), or equals the
parameter value if the input level exceeds the threshold.
When “Polarity” is negative, Control Target value equals the
parameter value if the input level is below the threshold, or is
obtained by multiplying the parameter value by the “Offset”
value if the level exceeds the threshold.
The “Attack” and “Release” parameters specify attack time and
release time of delay level control.
048: St. Auto Panning Dly
(Stereo Auto Panning Delay)
This stereo delay effect pans the delay sound left and right
using the LFO.
049: L/C/R BPM Delay
The L/C/R delay enables you to match the delay time with
the song tempo. You can also synchronize the delay time with
the arpeggiator or sequencer. If you program the tempo
before performance, you can achieve a delay effect that syn-
chronizes with the song in real-time. Delay time is set by
notes.
a
L Delay Time [msec]
Sets the delay time for the left channel 0.0...680.0msec
L Feedback
Sets the feedback amount for the left channel –100...+100
b
R Delay Time [msec]
Sets the delay time for the right channel 0.0...680.0msec
R Feedback
Sets the feedback amount for the right channel –100...+100
c
High Damp [%]
Sets the damping amount in the high range 0...100%
☞
Fx:043
Low Damp [%]
Sets the damping amount in the low range 0...100%
☞
Fx:043
d
LFO Waveform
Selects LFO Waveform Triangle, Sine
LFO Shape –100...+100
Determines how much the LFO waveform is changed
☞
Fx:020
e
LFO Phase [degree] –180...+180
Sets the LFO phase difference between the left and right
☞
Fx:034
Dynamic Delay
Threshold
Dry
Envelope
Wet
Control Target=Out
Polarity= (–)
Wet
Control Target=Out
Polarity= (+)
Delay Time
Time
(Ducking Delay)
Release
Attack
Level
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
LFO Phase
LFO Shape
Pan
Pan
LFO: Tri / Sin
Depth
Delay
Delay
High Damp Low Damp
High Damp Low Damp
Feedback
f
Panning Freq (Frequency) [Hz]
Sets the panning speed 0.02...20.00Hz
g
Panning Depth
Sets the panning width 0...100
Src Off...Tempo
Selects the modulation source for the panning width
Amt
Set the modulation amount of the panning width –100...+100
h
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance –100...+100
a
BPM
Selects MIDI Clock and assigns tempo MIDI, 40...240
☞
,
Time Over? > ----, OVER!!
Displays an error message when the delay time exceeds the upper
limit
☞
b
L Delay Base Note
Selects the type of notes to specify the delay time for TapL
☞
,
Times x1...x16
Sets the number of notes to specify the delay time for TapL
☞
Level
Sets the output level of TapL 0...50
c
C Delay Base Note
Selects the type of notes to specify the delay time for TapC
☞
,
Times x1...x16
Sets the number of notes to specify the delay time for TapC
☞
Level
Sets the output level of TapC 0...50
d
R Delay Base Note
Selects the type of notes to specify the delay time for TapR
☞
,
Times x1...x16
Sets the number of notes to specify the delay time for TapR
☞
Level
Sets the output level of TapR 0...50
e
Feedback (C Delay)
Sets the feedback amount of TapC –100...+100
Src Off...Tempo
Selects the modulation source for the TapC feedback
Amt –100...+100
Sets the modulation amount of the TapC feedback
C Delay
R Delay
Left
Right
Feedback
Spread
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Input Level D-mod
High Damp Low Damp
L Delay Input Level D-mod
+
Level
Level
Level
Tempo
BPM
BPM Base Note x Times
Base Note x Times
Base Note x Times