KORG Triton Studio - Manual (Page 292)

Appendices
281
[3] Parameters that are valid on the
TRITON STUDIO and TRITON but
invalid on the TRITON-Rack
3-1. Global mode parameters of the TRITON STU-
DIO and TRITON
Beep
Foot Switch Assign
Foot Pedal Assign
Damper Polarity
Foot Switch Polarity
• TRITON STUDIO or TRITON
→
TRITON-Rack
(.PCG file load/MIDI data dump)
These parameter settings are saved by the TRITON-Rack
as internal data, but are ignored. When the TRITON-
Rack saves this state as a .PCG file or performs a MIDI
data dump, the settings will be output in the condition in
which they were loaded or received via MIDI data dump.
• TRITON-Rack → TRITON STUDIO or TRITON
(.PCG file load/MIDI data dump):
These parameters will be set to their default values.
Convert Position
• TRITON STUDIO or TRITON
→
TRITON-Rack
(.PCG file load/MIDI data dump):
The PreMIDI or PostMIDI setting of this parameter is
saved by the TRITON-Rack as internal data, but is
ignored, and the TRITON-Rack will operate as if the set-
ting were PostMIDI. When the TRITON-Rack saves this
state as a .PCG file or performs a MIDI data dump, the
setting will be output in the condition in which it was
loaded or received via MIDI data dump.
• TRITON-Rack
→
TRITON STUDIO or TRITON
(.PCG file load/MIDI data dump):
This parameter will be set to “PostMIDI.”
MIDI Clock
• TRITON STUDIO or TRITON → TRITON-Rack
(.PCG file load/MIDI data dump):
The External PCI/F setting of this parameter is saved by
the TRITON-Rack as internal data, but is ignored, and
the TRITON-Rack will operate as if the setting were
External. When the TRITON-Rack saves this state as a
.PCG file or performs a MIDI data dump, the setting will
be output in the condition in which it was loaded or
received via MIDI data dump.
3-2. TRITON Combination and Sequencer mode
MIDI Filter “Enable Foot Pedal/Switch” param-
eter
• TRITON STUDIO or TRITON
→
TRITON-Rack
(.PCG/.SNG file load/MIDI data dump):
The parameter setting is saved by the TRITON-Rack as
internal data, but is ignored. When the TRITON-Rack
saves this state as a .PCG/.SNG file or performs a MIDI
data dump, the setting will be output in the condition in
which it was loaded or received via MIDI data dump.
• TRITON-Rack
→
TRITON STUDIO or TRITON
(.PCG/.SNG file load/MIDI data dump):
This parameter will be set to “On.”
3-3. TRITON STUDIO or TRITON Sequencer mode
parameters and data
Sequencer mode data of the TRITON STUDIO and TRI-
TON is compatible with the Multi mode data of the TRI-
TON-Rack via .PCG file load or MIDI data dump.
However, you must use caution regarding the following
parameters and data.
Meter
Tempo Mode
Track1-16 PLAY/MUTE
Track Play Loop
Track Play Loop Start Measure
Track Play Loop End Measure
Play Intro
• TRITON STUDIO or TRITON
→
TRITON-Rack
(.SNG file load/MIDI data dump):
These parameter settings are maintained by the TRITON-
Rack as internal data, but are ignored. When the TRI-
TON-Rack saves this state as a .PCG/.SNG file or per-
forms a MIDI data dump, the settings will be output in
the condition in which they were loaded or received via
MIDI data dump.
• TRITON-Rack → TRITON STUDIO or TRITON
(.SNG file load/MIDI data dump):
These parameters will be set to their default values.
Cue List data (Cue list setting data)
• TRITON STUDIO or TRITON
→
TRITON-Rack
(.SNG file load):
This data will not be loaded.
• TRITON STUDIO or TRITON
→
TRITON-Rack:
(MIDI data dump):
On the TRITON-Rack, this is saved as internal data of
Multi mode, but is ignored. When the TRITON-Rack per-
forms a MIDI data dump in this state, the settings will be
output in the condition in which they were received via
MIDI data dump.
Track data (Events of all song tracks)
• TRITON STUDIO or TRITON
→
TRITON-Rack
(.SNG file load):
This data will be loaded if you check Load track events?
(
☞“Load selected 15, 16”). On the TRITON-Rack, this
will be saved as internal data of Multi mode, but is not
used in Multi mode. This data will be output when the
TRITON-Rack saves a .SNG file.
• TRITON STUDIO or TRITON
→
TRITON-Rack
(MIDI data dump):
On the TRITON-Rack, this will be saved as internal data
of Multi mode, but is not used in Multi mode. This data
will be output when the TRITON-Rack transmits a MIDI
data dump.