KORG Triton Studio - Manual (Page 42)

Program
P0
P1
P2
P3
P4
P5
P7
P8
P9
31
☞For details on the master effects, refer to p.182 “8. Effect
Guide.”
9–1: Master FX
Here you can select the master effect types, switch them on/
off, specify chain order, and set the master EQ.
9–1a: MFX1, 2
The master effects do not output the direct sound (Dry). The
return level (“Return1,” “Return2”) sends the effect sound
(Wet) to the L and R bus, and this is mixed with the direct
sound (i.e., the output from P8: Routing tab “BUS Select” L/
R
, or the L/R output from Insert FX page “BUS Select”).
The master effects have a mono input. After passing through
the oscillator and insert effects, sound that is panned L and
R is mixed to a mono signal (as adjusted by the “Send 1” and
“Send 2” levels) and input to the master effects.
The master effects are mono-in stereo-out. Even when
a stereo-input type effect is selected, the input will be
monaural.
MFX1, 2 [000...089]
Selects the effect type for master effect 1 and 2. You can
select from 90 types of effect: 000: No Effect–089: Reverb-
Gate
. (Double-size effects cannot be selected.) If 000: No
Effect is selected, the output from the master effect will be
muted.
Category/MFX Select menu:
When you press the popup button, a “Category/MFX
Select” menu will appear. Press a tab to select the desired
category of effect, and select an effect from the list. Press the
OK button
to execute, or press the Cancel button to cancel.
MFX1, 2 On/Off [Off, ON]
Switches the master effects 1, 2 on/off. When off, the output
will be muted. This will alternate between on and off each
time it is pressed.
CC#94 can be used to switch the MFX on and off. A
value of 0 will be off, and a value of 1–127 will be the
original setting. This is controlled on the global MIDI
channel “MIDI Channel” (Global P1: 1–1a).
Chain [Off, On]
On (checked): Chain (series connection) will be turned on
for MFX1 and MFX2.
Off (unchecked):
MFX1 and MFX2 will operate in parallel.
Chain Direction [MFX1 →MFX2, MFX2→MFX1]
Specifies the direction of the connection when MFX1 and
MFX2 are chained.
MFX1
→
MFX2: Connect from MFX1 to MFX2.
MFX2
→
MFX1: Connect from MFX2 to MFX1.
Chain Signal [LR Mix, L Only, R Only]
When chain is On, this parameter specifies how the stereo
output signal of the first master effect will be connected to
the input (mono) of the next master effect.
L/R Mix: The stereo output L/R of the first master effect will
be mixed before being input to the next master effect.
L Only, R Only:
Only the left or right channel of the output
will be input to the next master effect.
Chain Level [000...127]
When chain is On, this sets the level at which the sound is
sent from the first master effect to the next master effect.
9–1b: Return Level
Return 1, 2 [000...127]
Adjusts the return levels from the master effects to the L/R
bus (main output L/MONO, R).
9–1c: Master EQ Gain [dB]
Sets the gain for the three-band EQ located immediately
before the sound of the L/R bus is sent from the AUDIO
OUTPUT (MAIN OUT) L/MONO and R jacks. This is
linked with the various “Gain” parameters of Master EQ (9–
4).
Low [–18.0...+18.0]
Mid [–18.0...+18.0]
High [–18.0...+18.0]
The cutoff frequency for “Low,” “Mid” and “High” and the
“Q” of “Mid” can be adjusted in the Master EQ page. These
settings are in “dB” units.
Program P9: Edit–Master Effect
9–1
9–1c
9–1a
9–1b