KORG Triton Studio - Manual (Page 208)

Ef
fect
197
g: High/Low Split Point
This parameter sets the frequency that splits the high and low
range. Only the high range will be sent to the chorus block.
h: Feedback
Sets the feedback amount of the chorus block. Increasing the feed-
back will allow you to use the effect as a flanger.
018: Multitap Cho/Delay
(Multitap Chorus/Delay)
This effect has four chorus blocks with a different LFO phase.
You can create a complex stereo image by setting each block’s
delay time, depth, output level, and pan individually. You can
also fix some of the chorus blocks to combine the chorus and
delay effects.
019: Ensemble
This Ensemble effect has three chorus blocks that use LFO to
create subtle shimmering, and gives three dimensional depth
and spread to the sound, because the signal is output from the
left, right, and center.
c: Shimmer
This parameter sets the amount of shimmering of the LFO wave-
form. Increasing this value adds more shimmering, making the
chorus effect more complex and richer.
a
LFO Frequency [Hz]
Sets the LFO speed 0.02...13.00Hz
b
Tap1(000) [msec]
Sets the Tap1 (LFO phase=0 degrees) delay time 0...570msec
Depth
Sets the Tap1 chorus depth 0...30
Level
Sets the Tap1 output level 0...30
Pan L6...L1, C, R1...R6
Sets the Tap1 stereo image
c
Tap2(180) [msec] 0...570msec
Sets the Tap2 (LFO phase=180 degrees) delay time
Depth
Sets the Tap2 chorus depth 0...30
Level
Sets the Tap2 output level 0...30
Pan L6...L1, C, R1...R6
Sets the Tap2 stereo image
d
Tap3(090) [msec] 0...570msec
Sets the Tap3 (LFO phase=90 degrees) delay time
Depth
Sets the Tap3 chorus depth 0...30
Level
Sets the Tap3 output level 0...30
Pan L6...L1, C, R1...R6
Sets the Tap3 stereo image
e
Tap4(270) [msec] 0...570msec
Sets the Tap4 (LFO phase=270 degrees) delay time
Depth
Sets the Tap4 chorus depth 0...30
Level
Sets the Tap4 output level 0...30
Pan L6...L1, C, R1...R6
Sets the Tap4 stereo image
f
Tap1 Feedback
Sets the Tap1 feedback amount –100...+100
Src Off...Tempo
Selects the modulation source of Tap1 feedback amount and effect
balance
Amt –100...+100
Sets the Tap1 feedback amount and modulation amount
Left
Right
Feedback Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
+ Level
Level
Level
Level
Pan
Pan
Pan
Pan
LFO: Triangle
Tap1 Delay
Tap2 Delay
Tap3 Delay
Tap4 Delay
0 [degree]
180 [degree]
90 [degree]
270 [degree]
g
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Amt
Sets the modulation amount of the effect balance –100...+100
a
Speed
Sets the LFO speed 1...100
Src
Selects the modulation source of LFO speed Off...Tempo
Amt
Sets the modulation amount of LFO speed –100...+100
b
Depth
Sets the depth of LFO modulation 0...100
Src Off...Tempo
Selects the modulation source of the LFO modulation depth
Amt –100...+100
Sets the modulation amount of the LFO modulation depth
c
Shimmer 0...100
Sets the amount of shimmering of the LFO waveform
☞
d
Wet/Dry Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Src Off...Tempo
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance –100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
LFO
Shimmer
+ Ensemble
Time
Level
Ensemble LFO
Shimmer