KORG Triton Studio - Manual (Page 132)

121
Sampling
P0
P1
P2
P3
P4
P5
P8
5–1b: Drive, Track, Index
Drive (Drive select) [ID0...6, CDD: Name]
Selects the CD-R/RW drive that contains the audio CD that
you want to play or rip.
Drives other than a CD-R/RW drive cannot be selected
here.
Track (Track Select) [01...]
Selects the track of the audio CD that you want to play or
rip.
Index [01...]
Selects the index of the audio CD that you want to play or
rip. This can be selected only if you have selected a track
that contains index data.
In the case of some CD-R/RW drives, index informa-
tion cannot be obtained.
5–1c: Volume
Volume [0...127]
Adjusts the volume of the audio signal that is output from
the CD-R/RW drive.
Some CD-R/RW drives do not support this, meaning
that this adjustment may not affect the volume.
5–1d: Ripping
Makes settings for ripping data from a CD.
If the cursor is located at “Range Start” or “Range End,” CD
playback will occur from “Range Start” to “Range End.”
Ripping is executed in the page menu command “Destina-
tion” (5–1A).
Range Start [00:00.0...]
Specify the starting location of the data that will be ripped.
When you re-select “Track” or “Index,” this will be reset to
00:00.0
.
If the cursor is located at “Range Start” or “Range End,”
pressing the [ENTER] key during playback will set
“Range Start” or “Range End” to the timing of that
moment. If you press the [ENTER] key two or more
times, the location at which the key was last pressed
will be specified.
If cursor is located at other than “Range Start” or
“Range End,” pressing the [ENTER] key once will spec-
ify “Range Start,” and pressing it once again will set
“Range End.” If you press the [ENTER] key three or
more times, the “Range Start” and “Range End” will be
set to the locations of the last press and the last-but-one
press.
Range End [00:00.0...]
Specifies the ending location of the data that will be ripped.
When you re-select “Track” or “Index,” this will be reset to
the ending time of the selected track or index.
Duration [00:00.0...]
Displays the length of time between “Range Start” and
“Range End.”
▼ 5–1: Page Menu Command
5–1A: Destination
Specifies the writing data of the ripped data, and execute
ripping. Ripping will create a stereo 44,100 Hz sample. You
can rip to sample memory (RAM), hard disk, floppy disk, or
a removable disk (sold separately) connected to the SCSI
connector. If you select Disk, a WAVE file will be created.
If the CDRW-1 option is installed, playing the keyboard
or operating the controllers during ripping may pro-
duce physical shock that causes data skips or reading
errors, preventing ripping from occurring normally.
Ripping to sample memory (RAM)
1 Select “Destination” to access the dialog box.
2 In the “To” field, select RAM.
3 In “Sample No.(L)” and “Sample No.(R),” specify the
destination to which the stereo sample data created by
ripping will be written.
By default, the lowest-numbered vacant sample will be
displayed. Normally you will leave this default setting
unchanged.
4 Press the OK button to execute ripping, or press the Can-
cel button
to cancel without executing.
Ripping to the hard disk or other disk
1 Select “Destination” to access the dialog box.
2 In the “To” field, select DISK.
3 Specify a name for the WAVE file that will be saved.
4 In “Drive select,” select the hard disk or other disk to
which the data will be saved.
5 Use the Open button and Up button to select the desired
directory on the save-destination disk.
6 Press the OK button to execute ripping, or press the Can-
cel button
to cancel without executing.
5–1A