KORG Triton Studio - Manual (Page 3)

iv
1. Program mode. . . . . . . . . . . . . 1
Program P0: Play ......................................... 1
Select and play programs.
0–1: Perf. Edit Select and play programs; use the
Performance Editor for simple editing
... 1
0–2: Arpeggio Arpeggio pattern selection and settings . 3
0–3: Sampling Perform sampling; make settings for
audio inputs etc.
......................................... 4
Program P1: Edit–Basic .................................. 7
Make basic oscillator settings and scale settings etc.
1–1: Program Basic Oscillator settings for Single/Double/
Drums, Poly/Mono, scale etc.
.................. 7
1–2: OSC Basic Specify the multisample for oscillators 1
and 2
............................................................ 9
1–3: Velo. Zone Velocity zone settings ............................. 11
1–4: Controller [SW1] and [SW2] key functions;
REALTIME CONTROLS [1]–[4] knob B-
mode functions
........................................ 12
Program P2: Edit–Pitch ................................. 12
Make pitch-related settings for oscillators 1 and 2.
2–1: OSC1 P.Mod Specify oscillator 1 pitch modulation via
key position or controllers
...................... 12
2–2: OSC2 P.Mod Specify oscillator 2 pitch modulation via
key position or controllers
...................... 14
2–3: Pitch EG Pitch EG settings ...................................... 14
Program P3: Edit–Filter ................................. 16
Make filter settings for oscillators 1 and 2.
3–1: Filter1 Filter 1 (for oscillator 1) type, cutoff
frequency, and resonance settings
........ 16
3–2: Filter1 Mod. Keyboard tracking and controller settings
to modulate the filter 1 cutoff frequency
.................................................................... 17
3–3: Filter1 LFO Mod. Filter 1 LFO settings to modulate the filter
1 cutoff frequency
.................................... 18
3–4: Filter1 EG Filter 1 EG settings ................................... 19
3–5: Filter2 Filter 2 (for oscillator 2) type, cutoff
frequency, and resonance settings
........ 21
3–6: Filter2 Mod. Keyboard tracking and controller settings
to modulate the filter 2 cutoff frequency
.................................................................... 21
3–7: Filter2 LFO Mod. Filter 2 LFO settings to modulate the filter
2 cutoff frequency
.................................... 21
3–8: Filter2 EG Filter 2 EG settings ................................... 21
Program P4: Edit–Amp .................................. 21
Make amp settings for oscillators 1 and 2.
4–1: Amp1 Level/Pan Oscillator 1 volume and pan settings .... 21
4–2: Amp1 Mod. Keyboard tracking and controller settings
to modulate amp 1
................................... 22
4–3: Amp1 EG Amp 1 EG settings ................................... 23
4–4: Amp2 Level/Pan Oscillator 2 volume and pan settings .... 24
4–5: Amp2 Mod. Keyboard tracking and controller settings
to modulate amp 2
................................... 24
4–6: Amp2 EG Amp 2 EG settings ................................... 24
Program P5: Edit–Common LFO ....................... 25
Make settings for the general purpose LFOs used to cycli-
cally modulate the pitch, filter, and amp of oscillators 1
and 2.
5–1: OSC1 LFO1 OSC1 LFO1 (for oscillator 1) settings .... 25
5–2: OSC1 LFO2 OSC1 LFO2 (for oscillator 1) settings .... 26
5–3: OSC2 LFO1 OSC2 LFO1 (for oscillator 2) settings .... 26
5–4: OSC2 LFO2 OSC2 LFO2 (for oscillator 2) settings .... 26
Program P7: Edit–Arpeggiator ......................... 26
Make settings for the arpeggiator.
7–1: Arpeg. Setup Select an arpeggio pattern and make
settings
....................................................... 26
7–2: Scan Zone Specify the note and velocity ranges that
will operate the arpeggiator
................... 28
Program P8: Edit–Insert Effect......................... 28
Specify the oscillator output bus, and make insert effect
settings.
8–1: Routing Specify the oscillator output bus and set
the send levels to the master effects
...... 28
8–2: Insert FX Select insert effects and turn them on/off,
and make chain settings
.......................... 29
8–3: IFX 1 Parameter settings for IFX1 .................... 30
8–4: IFX 2 Parameter settings for IFX2 .................... 30
8–5: IFX 3 Parameter settings for IFX3 .................... 30
8–6: IFX 4 Parameter settings for IFX4 .................... 30
8–7: IFX 5 Parameter settings for IFX5 .................... 30
Program P9: Edit–Master Effect ....................... 31
Make master effect and master EQ settings.
9–1: Master FX Select master effects and turn them on/
off, and make chain settings
................... 31
9–2: MFX 1 Parameter settings for MFX1 .................. 32
9–3: MFX 2 Parameter settings for MFX2 .................. 32
9–4: Master EQ Parameter settings for master EQ .......... 32
Table of Contents