KORG Triton Studio - Manual (Page 276)

265
Appendices
Universal system exclusive
Certain of the system exclusive messages are publicly
defined for a specific use, and these are called universal sys-
tem exclusive messages.
The TRITON STUDIO uses the following six universal sys-
tem exclusive messages.
Inquiry message request [F0, 7E, nn, 06, 01, F7]
Inquiry message [F0, 7E, nn, 06, 02, (nine bytes), F7]
When an inquiry message request is received, the TRITON
STUDIO will respond by transmitting an inquiry message
that means “I am a Korg TRITON STUDIO, with system ver-
sion ...”
GM system on [F0, 7E, nn, 09, 01, F7]
When this message is received in Song Play mode, the TRI-
TON STUDIO will be initialized for GM playback.
Master volume [F0, 7F, nn, 04, 01, vv, mm, F7]
(vv: lower byte of the value, mm: upper byte of the value,
together indicating 16384 steps)
This message is transmitted if you assign Master Volume as
the function of the ASSIGNABLE PEDAL or as a B-mode
function of a REALTIME CONTROLS [1]–[4] knobs and
operate the controller. This will adjust the overall volume
balance without changing the relative volume balance
between timbres/tracks. When this message is received, the
result will be the same as when the controller is operated.
Master balance [F0, 7F, nn, 04, 02, vv, mm, F7]
(vv: lower byte of the value, mm: upper byte of the value,
together indicating 16384 steps, where 8192 is the default
position, and lower values will move the sound toward the
left)
When this is received, the overall panning will be adjusted
without changing the relative panning between timbres/
tracks.
Master fine tuning [F0, 7F, nn, 04, 03, vv, mm, F7]
(A value of 8192 [mm, vv=40, 00] is center, 4096 [mm, vv=20,
00] is –50 cents, and 12288 [mm, vv=60, 00] is +50 cents.)
When this is received, the “Master Tune” (Global P0: 0–1a)
parameter will be set.
Master coarse tuning [F0, 7F, nn, 04, 04, vv, mm, F7]
(Normally only the upper byte mm is used. A value of 8192
[mm, vv=40, 00] is center, 6656 [mm, vv=34, 00] is –12 semi-
tones, and 9728 [mm, vv=4C, 00] is +12 semitones.)
When this is received, the “Transpose” (Global P0: 0–1a)
parameter will be set.
Transmitting sound settings data (Data Dump)
Data for programs, combinations, drum kits, user arpeggio
patterns, global settings, and sequencer data can be trans-
mitted as MIDI exclusive messages. The operation of send-
ing this system exclusive data to an external device is called
a “data dump.”
By performing a data dump, you can store the TRITON
STUDIO’s sounds and settings on an external device, or
rewrite the sounds and settings of another TRITON STU-
DIO.
There are the following three types of data dump.
• When you use the “Dump” (Global P1: 1–1) page menu
command to dump data, various types of internal
memory data will be transmitted. If this data is received
by the TRITON STUDIO, the data will be written
directly into internal memory, and it will not be
necessary to perform the Write operation.
(“Transmission,” “Reception”
☞p.145)
• If the “Enable Exclusive” (Global P1: 1–1b) setting is
checked, selecting a combination in Combination P0:
Play will transmit data for one combination. Selecting a
program in Program Play P0: Play will transmit data for
one program.
This data is the edit buffer data for the currently selected
combination or program. If this data is received by the
TRITON STUDIO, the data will be written into the edit
buffer, so if you wish to save it to internal memory, you
will need to perform the Write operation. The Write oper-
ation can also be performed by a MIDI exclusive Pro-
gram Write Request or Combination Write Request
message, in addition to the usual method of using the
TRITON STUDIO’s switches. (“Saving data”
☞BG p.55)
• If the “Enable Exclusive” (Global P1: 1–1b) setting is
checked, data will also be dumped in response to a
Dump Request message. This data is transmitted and
received on the global MIDI channel.
Editing sounds etc.
By using various MIDI exclusive data dumps, you can
rewrite all programs or an individual program. By using
parameter change messages, you can edit individual param-
eters as follows.
Parameter changes
• In Program mode, all parameters other than the program
name can be edited. Performance editor parameters are
included.
• In Combination mode, parameters other than the
combination name can be edited.
• In Sequencer mode, parameter changes can be used to
edit P0, 2, 3, 4 parameters other than “Location,”
“Meter,” “ (Tempo),” “Tempo Mode,” song name,
“Track Select,” “Reso,” “RPPR On/Off,” and P0:
Sampling, Preference. Parameter changes can also be
used to edit the P7: Arpeggiator, P8: Insert Effect, and
P9: Master Effect parameters.
Drum kit parameter change/User arpeggio pattern
parameter change
• In Global mode, you can edit drum kits and user
arpeggio patterns.
Since the other global parameters or Sequencer mode musi-
cal data cannot be edited, you will use data dumps to trans-
fer this data. Data dumping of Sampling mode data is not
supported.
The global MIDI channel is used to transmit and receive this
data.
First check “Enable Exclusive” (Global P1: 1–1b), so that
exclusive data can be transmitted and received. When you
change modes on the TRITON STUDIO, a mode change
message will transmitted. When you change programs or
combinations, the parameters for one program or one com-
bination will be transmitted together with the program
change. When you edit individual parameters, parameter
change, drum kit parameter change, user arpeggio pattern
parameter change messages or song parameter change mes-
sage will be transmitted.
When these messages are received, the same editing opera-
tion will be performed as on the transmitted device.
After MIDI exclusive data has been received and processed,
a Data Load Completed message will be transmitted. The
control master device must not transmit the next message
until this message is received (or until a sufficient interval of
time has elapsed).