KORG Triton Studio - Manual (Page 66)

55
Sequencer
P0
P1
P2
P3
P4
P5
P6
P7
P8
P9
0–3: Mixer 1–8
(Mixer T01–08)
0–4: Mixer 9–16
(Mixer T09–16)
Here you can set the pan and volume of each track.
The pan and volume that you specify here will be used
when you playback or record from the beginning of the
song. If you change the settings during recording, the
changes will be recorded as musical data, and pan and vol-
ume will change during playback. You can also change the
settings during playback. However when the song reaches a
location where pan or volume data was recorded, the set-
tings will change accordingly.
0–3(4)a: Track Number, Program Category, Pan,
Volume
Track Number (1...8 (9...16))
Indicates the track number. ( ☞0–1c/2c)
Program Category
Partially displays the name of the category used by the
track.
Pan [RND, L001...C064...R127]
Sets the pan of tracks 1–16.
L001...C064...R127: A setting of L001 is far left, and R127 is
far right. A setting of C064 will reproduce the pan setting of
the oscillator in Program mode.
If a mono-type insertion effect is inserted, this setting will be
ignored. In this case, the P8: Insert Effect, Insert FX page
“Pan (CC#8)” setting will adjust the pan of the sound fol-
lowing the insertion effect. (“3. Mixer”
☞p.181)
RND: The sound will be panned randomly at each note-on.
If “Status” (2–1a/2a) is INT or BTH, CC#10 Panpot can
be received to control the panning. When receiving
CC#10, a value of 0 or 1 is far left, 64 is center, and 127 is
far right. When you change the song or return to the
beginning of the song, tracks whose “Status” is EXT,
EX2
or BTH will transmit the pan you specify here as a
MIDI message (except for RND).
Volume [000...127]
Sets the volume of tracks 1–16.
When “Status” (2–1a/2a) is INT or BTH, CC#7 Volume
can be received to control the volume. The volume of a
track is determined by multiplying the MIDI Volume
(CC#7) and Expression (CC#11) values. When you
change the song or return to the beginning of the song,
tracks whose “Status” is EXT, EX2 or BTH will transmit
the volume you specify here as a MIDI Volume mes-
sage.
0–5: PlyLoop 1–8
(PlayLoop T01–08)
0–6: PlyLoop 9–16
(PlayLoop T09–16)
When playing or recording a song, you can independently
loop the playback of tracks 1–16.
0–5(6)a: Play Loop, Loop Start Measure, Loop End
Measure, Play Intro
Track Play Loop [Off, On]
Turns looping on/off for each track 1–16.
On (checked): That track will loop between “Loop Start
Measure” and “Loop End Measure.”
Loop Start Measure [001...999]
Specifies the first measure of the loop.
Loop End Measure [001...999]
Specifies the last measure of the loop.
Play Intro [Off, On]
On (checked) : After the measures before the specified “Loop
Start Measure” are played once, the region of “Loop Start
Measure” – “Loop End Measure” will be played repeatedly.
For example, you can use this on a drum track to make it
play a fill-in and then begin looping.
Off (unchecked)
: Playback will begin from the “Loop Start
Measure,” and will begin looping immediately.
This will be valid if “Track Play Loop” is checked and
“Loop Start Measure” is set to other than 001.
0–1
0–1a
0–3a
0–1b
OSC1: Amp1 Pan=L001
OSC2: Amp2 Pan=R127
Left Center Right
Pan (CC#10)
C064
Left Center Right
L032
L001
R096
R127
Left Center Right
Left Center Right
OSC1 OSC2
OSC1: Amp1 Pan=L032
OSC2: Amp2 Pan=R096
Pan (CC#10)
C064
L032
L001
R096
R127
OSC1: Amp1 Pan=C064
OSC2: Amp2 Pan=C064
Left Center Right
Pan (CC#10)
C064
Left Center Right
L032
L001
R096
R127
OSC1 OSC2
0–1
0–1a
0–5a
0–1b
0–3a