Yokogawa DR240 - Manual (Page 14)

13 IM DR232-01E
List of Menus and Set-up Data
The following is a list of set-up data, procedures to switch to different setting modes, and setting
menu.
Measurement Condition Settings
Parameters Procedure Selecting menu Reference
Input type, span, linear RANGE key 001-01:VOLT/2V Chapter 5
scaling* 1
Units SET key* 2 SET=UNIT Section 6.1
Moving average Press the SET key for about three seconds* 2 SET=MOVE AVE Section 6.8
Measurement cycle* 1 Turn ON power while pressing the DISP key SET UP= Section 10.1
SCAN INTVL
A/D integration time* 1 Turn ON power while pressing the DISP key SET UP=A/D INTG Section 10.3
Filter* 1 Turn ON power while pressing the DISP key SET UP=FILTER Section 10.3
*1: Make sure that the total number of setting changes, including calibrations and restructuring, does not
surpass 100000.
*2: Procedure varies according to the menu configuration of the SET key (see section 10.9).
Chart Speed Settings
Parameters Procedure Selecting menu Reference
Chart speed 1 CHART key CHART Section 6.2
Chart speed 2 Press the SET key for about three seconds* SET=CHART2 Section 6.2
*: Procedure varies according to the menu configuration of the SET key (see section 10.9).
Recording Settings
Parameters Procedure Selecting menu Reference
Logging/Analog trend SET key* SET=SYSTEM Section 6.1
switch, dot-printing cycle
Recording channel
SET key* SET=TREND Section 6.1
Recording zone Press the SET key for about three seconds* SET=ZONE Section 6.3
Partial compression Press the SET key for about three seconds* SET=PERTIAL Section 6.3
Tag Press the SET key for about three seconds* SET=TAG Section 6.4
Channel to digital print, Press the SET key for about three seconds* SET=DIGITAL PR Section 6.4
number of rows to print
Channel to manual print Press the SET key for about three seconds* SET=MANUAL PR Section 6.4
Alarm print
Press the SET key for about three seconds* SET=ALARM PR Section 6.5
Channel to print scale Press the SET key for about three seconds* SET=SCALE PR Section 6.6
values
Channel to list print
Press the SET key for about three seconds* SET=LIST PR Section 6.6
Items to list print Press the SET key for about three seconds* SET=LIST FMT Section 6.6
Message Press the SET key for about three seconds* SET=MESSAGE Section 6.7
Header Press the SET key for about three seconds* SET=HEADER Section 6.7
Title Press the SET key for about three seconds* SET=TITLE Section 6.7
Interpolation Press the SET key for about three seconds* SET=INTERPOL Section 6.8
Adjust dot-printing Turn ON power while pressing the DISP key SET UP=PRN ADJ Section 10.1
position
Recording format
Turn ON power while pressing the DISP key SET UP=RECORD Section 10.2
Dot-print color Turn ON power while pressing the DISP key SET UP=COLOR Section 10.6
*: Procedure varies according to the menu configuration of the SET key (see section 10.9).
Display Settings
Parameters Procedure Selecting menu Reference
Switch display DISP key and MODE key -------- Chapter 4
Display update interval Turn ON power while pressing the SET UP=DISPLAY Section 10.10
DISP key
Alarm Settings
Parameters Procedure Selecting menu Reference
Alarm, alarm output ALARM key 001-01:1/OFF Section 8.1
relay
Alarm
Turn ON power while pressing the DISP key SET UP=ALARM Section 10.3
interval/hysteresis/hold
Execute alarm
FUNC key* ALARM ACK Section 9.3
acknowledge
Reset alarm
FUNC key* ALARM RST Section 9.3
Clear alarm buffer Press the FUNC key for about three seconds* ALM BUF CLEAR Section 9.4
*: Procedure varies according to the menu configuration of the FUNC key (see section 10.8).