Brocade Multi-Service IronWare Routing Configuration Guide (Supporting R05.6.00) - Manual (Page 758)

730 Multi-Service IronWare Routing Configuration Guide
53-1003033-02
Displaying IPv6 IS-IS information
You can display the detailed information of all the LSPs in the LSP databases with IS-IS MT
transition support enabled or disabled, by entering the following command at any level of the CLI.
The following example shows the output for the show ipv6 isis database detail command without
the transition support.
Brocade# show ipv6 isis database detail
IS-IS Level-1 Link State Database
LSPID Seq Num Checksum Holdtime ATT/P/OL
Dist1.00-00 0x000001b2 0x0ed4 1183 0/0/0
Area Address: 00.0000
NLPID: IPv6 IP
Topology: IPv6(Ovld:0 Att:0) IPv4
Hostname: Dist1
IP address: 101.1.1.1
IPv6 address: 2000:56:1::1:1:1
Metric: 10 IP-Extended 191.56.1.0/24 Up: 0 Subtlv: 0
Metric: 10 IP-Extended 191.25.1.0/24 Up: 0 Subtlv: 0
Metric: 10 IP-Extended 191.1.5.1/32 Up: 0 Subtlv: 0
Metric: 10 IPv6 (MT-IPv6) 2000:56:1:0:0:1::/96 Up: 0 Subtlv: 0
Metric: 10 IPv6 (MT-IPv6) 2000:25:1:0:0:1::/96 Up: 0 Subtlv: 0
Metric: 10 IPv6 (MT-IPv6) 2000:1:1::5:1/128 Up: 0 Subtlv: 0
Metric: 10 IS (MT-IPv6) Dist2.00
Metric: 10 IS (MT-IPv6) Edge2.00
Metric: 10 IS-Extended Dist2.00
Metric: 10 IS-Extended Edge2.00
LSPID Seq Num Checksum Holdtime ATT/P/OL
Core2.00-00 0x00000049 0xee12 1174 0/0/0
Area Address: 00.0000
NLPID: IPv6 IP
Topology: IPv6(Ovld:0 Att:0) IPv4
Hostname: Core2
IP address: 102.1.1.2
IPv6 address: 2000:28:1::1:1:2
Metric: 10 IP-Extended 191.28.1.0/24 Up: 0 Subtlv: 0
Metric: 10 IP-Extended 191.68.1.0/24 Up: 0 Subtlv: 0
Metric: 10 IP-Extended 191.1.8.1/32 Up: 0 Subtlv: 0
Metric: 10 IPv6 (MT-IPv6) 2000:28:1:0:0:1::/96 Up: 0 Subtlv: 0
Metric: 10 IPv6 (MT-IPv6) 2000:68:1:0:0:1::/96 Up: 0 Subtlv: 0
Metric: 10 IPv6 (MT-IPv6) 2000:1:1::8:1/128 Up: 0 Subtlv: 0
Metric: 10 IS (MT-IPv6) Dist2.12
Metric: 10 IS (MT-IPv6) Core2.3c
Metric: 10 IS (MT-IPv6) Core2.3d
Metric: 10 IS (MT-IPv6) Edge2.00
ATT A 4-bit value extracted from bits 4 – 7 in the Attach field of the LSP.
P The value in the Partition option field of the LSP. The field can have one of the
following values:
•
0 – The IS that sent the LSP does not support partition repair.
•
1 – The IS that sent the LSP supports partition repair.
OL The value in the LSP database overload field of the LSP. The field can have one
of the following values:
•
0 – The overload bit is off.
•
1 – The overload bit is on, indicating that the IS that sent the LSP is
overloaded and should not be used as a Level-2 router.
TABLE 153 IPv6 IS-IS summary LSP database information (Continued)
This field... Displays...