CONTREX CX-1200 - Manual (Page 416)

C - 70
(Continued)
Appendix C: Parameter Summary Numeric Quick Reference (continued)
CP-449 Lg Number Units
Use Large Number Units (CP-449) to select the EU text that displays immediately below the Large Number Display on
the Status screen (refer to the status screen in Operation: Screen Operation). Enter a numeric code that identifies the
EU for the Control Parameter displayed in the Large Number Parameter (CP-440). Refer to the numeric code list below.
The Help screen for CP-449 also contains a partial list of numeric code options. In addition, you can also scroll through
the numeric code options by accessing CP-449 with the Code key while you are in the in the Status screen.
0 = <BLANK> 1 = RPM (default) 2 = Hertz
3 = KHz 4 = EU/sec 5 = EU/min
6 = EU/hr 7 = Units/sec 8 = Units/min
9 = Units/hr 10 = Inches/sec 11 = Inches/min
12 = Feet/sec 13 = Feet/min 14 = Feet/hr
15 = Yards/min 16 = Yards/hr 17 = CM/sec
18 = CM/min 19 = Meters/min 20 = Meters/hr
21 = Gal/sec 22 = Gal/min 23 = Gal/hr
24 = Liters/sec 25 = Liters/min 26 = Liters/hr
27 = Sec/unit 28 = Sec/inch 29 = Sec/foot
30 = Sec/CM 31 = Sec/gal 32 = Sec/liter
33 = Min/unit 34 = Min/inch 35 = Min/foot
36 = Min/yard 37 = Min/CM 38 = Min/meter
39 = Min/gal 40 = Min/liter 41 = Hr/unit
42 = Hr/foot 43 = Hr/yard 44 = Hr/meter
45 = Hr/gal 46 = Hr/liter 47 = Feet/foot
48 = Ratio 49 = Percent (%) 50 = Seconds
51 = Minutes 52 = Hours 53 = EU
54 = EU/Tm 55 = EU/Tm/sec 56 = Units
57 = Inches 58 = Feet 59 = Yards
60 = Centimeters 61 = Meters 62 = Gallons
63 = Liters 64 = lb 65 = Counts
66 = Pulses 67 = Lines 68 = Revs
69 = Degrees 70 = Pulses/Rev 71 = Pulses/EU
72 = Volts 73 = Milliamps 74 = Bits
75 = Bits/sec 76 = Volts/kiloEU 77 = oz
78 = psi 79 = newton 80 = Custom (user defined through the serial com)
Minimum Value: 0 Maximum Value: 80
Default Value:1 RPM (default) Units: Coded
CP-450 Diagnostics En
When Diagnostics Enable (CP-450) is set to “1” (On or enabled), the digital inputs will not recognize their normal
function and the digital outputs can be controlled by Diag DO (CP-452). In addition, the CO_Sig Control Output can be
tested. When you enter diagnostics, Diag DO (CP-452) is forced equal to the current DO 7..0 (MP-102) so that there is
no unexpected change in the outputs. Change the outputs through Diag DO (CP-452) while performing the diagnostics.
Warning: The actuator may energize if you change Diag DO (CP-452). Stand clear of the system.
1 = On
0 = Off (default)
Minimum Value: 0 Maximum Value: 1
Default Value: 0 Units: Coded