TANDBERG 6000MXP - Manual (Page 216)

216
TANDBERG 3000 MXP & 6000 MXP
REFERENCE GUIDE FOR SYSTEM INTEGRATORS
D 13887.08
MAY 2008
Status information followed by a
*
will not be shown unless Detailed Level has been set to 2 – see XACLI – Special commands – xpreferences
Cause No. 31 - Normal, Unspecified
This cause is used to report a normal event only when no other cause in
the normal class applies.
Cause No. 34 - No Circuit/Channel Available
This cause indicates that there is no appropriate circuit/channel
presently available to handle the call. Note: If you receive this call, try
another data-service, such as dropping from a 64K to 56K data rate.
Cause No. 35 - Call Queued
This cause indicates that the call has been queued for service by the
next available device.
Cause No. 38 - Network Out Of Order
This cause indicates that the network is not functioning correctly and
that the conditions are likely to last a relatively long period of time.
A call that is attempted soon afterwards will most likely not connect
successfully.
Cause No. 39 - Permanent Frame Mode Connection Out-Of-Service
This cause is included in a STATUS message to indicate that a perma-
nently established frame mode connection is out-of-service (e.g. due to
equipment or section failure) [see Annex A/Q.933].
Cause No. 40 - Permanent Frame Mode Connection Operational
This cause is included in a STATUS message to indicate that a perma-
nently established frame mode connection is operational and capable
of carrying user information. [see Annex A/Q.933].
Cause No. 41 - Temporary Failure
This cause indicates that the network is not functioning correctly and
that the condition is not likely to last a very long period of time. A call
that is attempted almost immediately afterwards will most likely con-
nect successfully.
Cause No. 42 - Switching Equipment Congestion
This cause indicates that the switching equipment generating this
cause is experiencing a period of high traffic.
Cause No. 43 - Access Information Discarded
This cause indicates that the network could not deliver access informa-
tion, low layer compatibility, high layer compatibility, or sub-address as
indicated in the diagnostic.
Cause No. 44 - Requested Circuit/Channel Not Available
This cause is returned when the circuit or channel indicated by the
requesting entity cannot be provided by the other side of the interface.
Cause No. 46 - Precedence Call Blocked
This cause indicates that there are no preemptable circuits or that the
called user is busy with a call of equal or higher preemptable level.
Cause No. 47 - Resource Unavailable, Unspecified
This cause is used to report a resource unavailable event only when no
other cause in the resource unavailable class applies.
Cause No. 49 - Quality Of Service Not Available
This cause is used to report that the requested Quality of Service can-
not be provided (delay canít be supported).
Cause No. 50 - Requested facility not subscribed
This cause indicates that the requested supplementary service could
not be provided due to user oversight. This cause code is often caused
by the CPE being configured for the wrong switch type.
Cause No. 52 - Outgoing calls barred
This cause indicates that because of call screening provided by the
network, the calling user is not permitted to make a call.
Cause No. 53 - Outgoing Calls Barred Within CUG
This cause indicates that although the calling party is a member of the
CUG for the outgoing CUG call, outgoing calls are not allowed for this
member of the CUG.
Cause No. 54 - Incoming calls barred
This cause indicates that the called user will not accept the call deliv-
ered in the SETUP message.
Cause No. 55 - Incoming Calls Barred Within CUG
This cause indicates that although the calling party is a member of the
CUG for the incoming CUG call, incoming calls are not allowed for this
member of the CUG.
Cause No. 57 - Bearer Capability Not Authorized
This cause indicates that the user has requested a bearer capability
which is implemented by their equipment but the user is not authorized
to use.
Cause No. 58 - Bearer Capability Not Presently Available
This cause indicates that the user has requested a bearer capability
which is implemented by the equipment which generated this cause but
which is not available at this time.
Cause No. 62 - Inconsistency In Outgoing Information Element
This cause indicates an inconsistency in the designated outgoing ac-
cess information and subscriber class.
Cause No. 63 - Service Or Option Not Available, Unspecified
This cause is used to report a service or option not available event
only when no other cause in the service or option not available class
applies.
Cause No. 65 - Bearer Capability Not Implemented
This cause indicates that the equipment sending this cause does not
support the bearer capability requested.
Cause No. 66 - Channel Type Not Implemented
This cause indicates that the equipment sending this cause does not
support the channel type requested.
Cause No. 69 - Requested Facility Not Implemented
This cause indicates that the equipment sending this cause does not
support the requested supplemental service.
Cause No. 70 - Only Restricted Digital Information Bearer Capability
Is Available
This cause indicates that on equipment has requested an unrestricted
bearer service but that the equipment sending the cause only supports
the restricted version of the requested bearer capability.
Cause No. 79 - Service Or Option Not Implemented, Unspecified
This cause is used to report a service r option not implemented but only
when no other cause in this class applies.
Status Information – xhistory / xhistory.xml
Call - DisconnectCauseValue (2:3)