TANDBERG 6000MXP - Manual (Page 23)

23 D 13887.08
MAY 2008
TANDBERG 3000 MXP & 6000 MXP
REFERENCE GUIDE FOR SYSTEM INTEGRATORS
Interfaces and Sockets – Codec 3000 MXP
Single
S-video output
Mini-DIN socket
S-video input
Mini-DIN socket
Aux. camera
Single Dual
Composite video output
RCA sockets
Composite video input RCA sockets
Doc. camera VCR
PC DVI-I input sockets
(Digital Video Interface,
Integrated digital
and analogue)
DVI output
NoTe! The system
will automatically
adapt to a PAL or
NTSC input.
DVI-I Pin-out
Pin Assignment Pin Assignment Pin Assignment
1 T.M.D.S. Data 2– 9 T.M.D.S. Data 1– 17 T.M.D.S. Data 0–
2 T.M.D.S. Data 2+ 10 T.M.D.S. Data 1+ 18 T.M.D.S. Data 0+
3 T.M.D.S. Data 2/4
Shield 11 T.M.D.S. Data 1/3
Shield 19 T.M.D.S. Data 0/5
Shield
4 T.M.D.S. Data 4– 12 T.M.D.S. Data 3– 20 T.M.D.S. Data 5–
5 T.M.D.S. Data 4+ 13 T.M.D.S. Data 3+ 21 T.M.D.S. Data 5+
6 DDC Clock 14 +5 V power 22 T.M.D.S. Clock
Shield
7 DDC Data 15 GND
(return for +5 V,
HSync and Vsync) 23 T.M.D.S. Clock+
8 Analogue Vertical
Sync 16 Hot plug detect 24 T.M.D.S. Clock–
C1 Analogue Red C2 Analogue Green C3 Analogue Blue
C4 Analogue
Horizontal Sync C5 Analogue GND
(analogue
R, G & B return)
DVI-I pin-out
Note: TANDBERG supports DVI-D
Single-Link, DVI-A and DVI-I Sin-
gle-Link format cables.
DVI-D cables transmit digital
T.M.D.S. signals, DVI-A cables
transmit analogue VGA signals
and DVI-I cables can transmit
either digital or analogue signals.
If your DVI cable is not long
enough, use extension cables.
Observe, however, that the
maximum cable length should not
exceed 5 m to avoid quality loss.
Formats supported on DVI-I out:
SVGA (800 × 600) 75 Hz
XGA (1024 × 768) 60 Hz
SXGA (1280 × 1024) 60 Hz
HD720p (1280 × 720) 50 Hz, 60 Hz
WXGA (1280×768) 60 Hz
Formats supported on DVI-I in:
SVGA (800 × 600) 60 Hz, 72 Hz, 75 Hz, 85 Hz
XGA (1024 × 768) 60 Hz, 70 Hz, 75 Hz
SXGA (1280 × 1024) 60 Hz
HD720p (1280 × 720) 50 Hz, 60 Hz
Levels
Composite: 1 Vpp, 75 W
S-Video (Y/C):
Y: 1 Vpp, 75 W
C (PAL): 0.3 Vpp, 75 W
C (NTSC): 0.28 Vpp, 75 W
Do as follows to get WXGA:
1 VGA Out Quality must be set to Auto .
2 VGA Monitor Format must be set to Wide .
3 PC Picture Format must be set to Normal .
If you are using TANDBERG supplied monitors this will give WXGA out
when displaying graphics.
If non-TANDBERG provided displays are used, you must in addition
execute the command:
xConfiguration Video Outputs AllowWXGA: On
Video Sockets
GND
RCA pin-out
External view of socket
Signal
S-video Mini-DIN pin-out
External view of socket
Pin 1: Ground (Luminance)
Pin 2: Ground (Chrominance)
Pin 3: Luminance (Y)
Pin 4: Chrominance (C)
1
3 4
2