Yokogawa EJX440A - Manual (Page 16)

<3. Operation>
3-6
IM 01C25T01-01E
3.3 Menu Tree
1 Device setup
2 Pres
3 AO
4 LRV
5 URV
1 Process variables
2 Diag/Service
3 Basic setup
4 Detailed setup
5. Review
1 Pres
2 Pres %
3 AO
4 SP
5 SP %
6 Snsr temp
7 Engr Disp
8 Engr exp
9 Engr Unit
1 Status group 1
2 Status group 2
3 Status group 3
4 Status group 4
5 Status group 5
6 Status group 6
7 Status group 7
8 Status group 8
9 Status group 9
1 Keypad input
2 Apply values
1 D/A trim
2 Scaled D/A trim
3 Clear D/A trim
1 Pres Zero trim
2 Pres trim
3 P LTP
4 P UTP
5 Pres trim info.
1 Pres
2 Pres %
3 SP
4 Snsr temp
1 Pres
2 Pres %
3 Unit
4 Pres sensor trim
1 SP
2 SP %
3 SP Unit
4 A/G Select
5 SP H/L Select
6 SP sensor trim
7 SP setup
1 Pres
2 Pres %
3 AO
4 SP
5 SP %
6 Snsr temp
7 Engr Disp
8 Engr exp
9 Engr Unit
Digital Output
1 Loop test
2 D/A trim
3 Scaled D/A trim
4 Clear D/A trim
5 AO alm typ
6 Auto recover
7 AO lower limit
8 AO upper limit
1 Poll addr
2 Num req preams
3 Burst mode
4 Burst option
1 Pres Alert mode
2 Config Pres Alerts
3 SP Alart mode
4 Config SP Alerts
5 Temp Alert mode
6 Config Temp Alerts
7 DO Config 1 Disp Out 1
2 Disp Out 2
3 Disp Out 3
4 Disp Out 4
1 Universal rev
2 Fld dev rev
3 Software rev
1 S.C.
2 Num of points
3 Point setting
1 P LTD
2 P UTD
3 Clear P snsr trim
1 SP LTD
2 SP UTD
3 Clear SP snsr trim
1 Disp Pres % fnctn
2 Disp Pres % Reso
3 Pres disp point
1 Engr LRV
2 Engr URV
3 Engr exp
4 Engr Unit
5 Engr point
6 Set Engr Unit
7 Modify Engr Unit
1 Keypad input
2 Apply values
1 Date
2 Descriptor
3 Message
4 Write Protect
1 Static Pres trim
2 SP LTP
3 SP UTP
4 SP trim info.
1 Trim Who
2 Trim Date
3 Trim Loc
4 Trim Desc
1 Digital Output
2 DO Select
3 DO Signal type
4 DO Test
1 Pres Zero trim
2 Pres trim
3 P LTP
4 P UTP
5 Pres trim info.
1 Static Pres trim
2 SP LTP
3 SP UTP
4 SP trim info.
1 T.Z. Cmp mode
2 Temp Zero
1 SP Range
2 SP Unit
3 SP Damp
4 SP A/G Setup
5 SP H/L Select
1 Tag
2 Date
3 Descriptor
4 Message
5 Model 1
6 Model 2
7 Model 3
8 Write Protect
9 Ext SW
Revision #s
Additional Info
1 Status
2 Self test
1 Re-range
2 Analog output trim
3 Pres sensor trim
4 SP sensor trim
5 Trim info.
1 Error log view
2 Error log Clear
1 Process variables
2 Re-range
3 Unit
4 Xfer fnctn
5 Pres Damp
6 Low cut
7 Low cut mode
8 H/L Swap
9 Bi-dir mode
Quick resp
T.Z. Cmp menu
S.C. menu
1 Process variables
2 Analog output
3 HART output
4 Process Alerts
1 Disp select
2 P disp condition
3 SP disp condition
4 Engr disp range
5 Bar Indicator
1 Field device info
2 Sensor information
3 Self test
1 Pressure sensor
2 SP sensor
3 Temp sensor
1 Keypad input
2 Apply values
1 Linear
2 Sq root
Linear
Zero
Normal
Reverse
1 Snsr temp
2 Amp temp
3 Temp Unit
1 Test device
2 Loop test
3 Calibration
4 Diag Parameters
5 Error log
Online Menu
(Device setup) (Process variables) (Diag/Service)
1 Tag
2 Unit
3 Re-range
4 Device information
5 Xfer fnctn
6 Pres Damp
7 Low cut
8 Low cut mode
9 H/L Swap
SP setup
(Basic setup)
1 Sensors
2 Signal condition
3 Output condition
4 Display condition
5 Device information
6 Test Key
(Detailed setup)
1 Keypad Input
2 Wrt protect menu
Hot Key
1 LRV
2 URV
3 Unit
4 LSL
5 USL
6 Min Span
1 Write protect
2 Enable wrt 10min
3 New password
4 Software seal
F0307-1.ai
See A
(next page).