Yokogawa EJX440A - Manual (Page 62)

<5. Parameter Summary>
5-1
IM 01C25T01-01E
5. Parameter Summary
Function Label Item Contents Default value Handling
Fast key
sequences
Analog output AO alm typ Analog output alarm type High or Low R 1, 4, 3, 2, 5
AO lower limit Lower limit of analog output 3.6000 to 21.6000 mA 3.6000 mA W 1, 4, 3, 2, 7
AO upper limit Upper limit of analog output 3.6000 to 21.6000 mA 21.6000 mA W 1, 4, 3, 2, 8
Auto recover Auto-recover from hardware error Off or On On W 1, 4, 3, 2, 6
Analog output
trim
Clear D/A trim Reset analog output trim M 1, 2, 3, 2, 3
D/A trim Analog output trim with ammeter M 1, 2, 3, 2, 1
Scaled D/A trim Analog output trim with voltmeter M 1, 2, 3, 2, 2
Bi-directional
mode
Bi-dir mode Bi-directional mode Off or On Off W 1, 4, 2, 9
Burst mode Burst mode Burst mode Off or On Off W 1, 4, 3, 3, 3
Burst
operation
option
Burst option Burst option PV, % range/current, or
Process vars/cmt
W 1, 4, 3, 3, 4
Damping Pres Damp Damping time constant at amplifier 0.00 to 100.00 sec As specified or
2.00 sec
W 1, 3, 6
Quick resp Quick response On or Off Off W 1, 4, 2, ↓
Date Date Date **/**/** W 1, 3, 4, 1
Descriptor Descriptor Descriptor 16 alphanumerics As specified W 1, 3, 4, 2
Device
information
Dev id Device ID R 1, 4, 5, 1, ↓, 6
Distributor Yokogawa R 1, 4, 5, 1, ↓, 7
Drain vent matl Drain and vent plug material W 1, 4, 5, 2, 5
Extra No. Customization number R 1, 4, 5, 1, ↓, 4
Ext SW External zeroing permission Disabled or Enabled Enabled W 1, 4, 5, 1, 9
Fill fluid Fill fluid W 1, 4, 5, 2, 2
Final asmbly num Final assembly number W 1, 4, 5, 1, ↓, 5
Fld dev rev Field device revision R 1, 4, 5, 1, ↓, 2
Gasket matl Gasket material W 1, 4, 5, 2, 3
Isoltr matl Capsule material W 1, 4, 5, 2, 1
LSL Lower sensor limit R 1, 3, 3, 1, 4
Mftr Date Manufactured date R 1, 4, 5, 1, ↓, 3
Min span Minimum span R 1, 3, 3, 1, 6
Model 1 Memo field for MS code 1 32 alphanumerics W 1, 4, 5, 1, 5
Model 2 Memo field for MS code 2 32 alphanumerics W 1, 4, 5, 1, 6
Model 3 Memo field for MS code 3 32 alphanumerics W 1, 4, 5, 1, 7
Num of RS Number of remote seal W 1, 4, 5, 2, 9
Process Conn matl Process connection material W 1, 4, 5, 2, 4
Process Conn size Process connection size W 1, 4, 5, 2, 8
Process Conn type Process connection type W 1, 4, 5, 2, 6
RS fill fluid Fill fluid of remote seal W 1, 4, 5, 2, ↓
RS Isoltr matl Remote seal material W 1, 4, 5, 2, 7
RS type Remote seal type W 1, 4, 5, 2, ↓
Serial No. Serial number R 1, 4, 5, 1, ↓, 2
Software rev Software revision R 1, 4, 5, 1, ↓, 3
Style No. Style number Style number of product R 1, 4, 5, 1, ↓, 1
Universal rev Universal revision R 1, 4, 5, 1, ↓, 1
USL Upper sensor limit R 1, 3, 3, 1, 5
Diag
Applicable
Diag Applicable Appicable blockage detection Disabled or Enabled R, G 1, 2, 4, 3, 1, 2
Diag
DPComp
Diag DPComp fDP compensation selection 0: Compensation or
1: Non-compensation
0:
Compensation
W, G 1, 2, 4, 3, 2, 7
Diag Error Diag Error Results detected by ILBD or Heat
trace monitoring
R, G 1, 2, 4, 1
*1: Handling: R=Read only, W=Read & Write, M=Method, A=Applicable for option code AL, G=Applicable for option code DG6,
D=Applicable for differential pressure transmitters. Do not change these parameters for pressure transmitters.
*2: The default value shows MWP (Maximum working pressure) of the capsule.
Since the working pressure limit varies according to the Model, refer to the General Specifications section in each user’s manual.