Rockwell Automation 1753-PCS-PAR Using RSLogix Guard PLUS! with GuardPLC Controllers - Manual (Page 5)

v Publication 1753-PM001A-EN-P - November 2005
Table of Contents
Preface
Who Should Use This Manual . . . . . . . . . . . . . . . . . . . . . . P-1
Purpose of this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . P-1
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . P-1
Chapter 1
Connect to the GuardPLC
Controller In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Connect to the Controller via RSLogix Guard PLUS! Software 1-1
Connect to a GuardPLC 1200 Controller . . . . . . . . . . . . 1-1
Connect to a GuardPLC 1600 or 1800 Controller . . . . . . 1-2
Connect to a GuardPLC 2000 Controller . . . . . . . . . . . . 1-2
GuardPLC Controller Factory Default Settings . . . . . . . . 1-2
Understand Ethernet Addressing . . . . . . . . . . . . . . . . . . 1-2
Configure the IP Address of Your Programming Terminal 1-3
Go Online with the GuardPLC Controller . . . . . . . . . . . . . . 1-5
Step 1: Open RSLogix Guard PLUS! Software. . . . . . . . . 1-6
Step 2: Create a New Project . . . . . . . . . . . . . . . . . . . . 1-6
Step 3: Configure the Controller Type and SRS . . . . . . . 1-7
Step 4: Get Communication Settings . . . . . . . . . . . . . . . 1-9
Step 5: Change Settings via MAC Address . . . . . . . . . . . 1-10
Step 6: Move the Settings Into Your Offline Project . . . . 1-11
Step 7: Use the Control Panel to Connect to the
GuardPLC Controller . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
Step 8: Change the Controller to STOP Mode . . . . . . . . 1-14
Step 9: Reset the Controller to the Default Settings . . . . 1-14
Step 10: Ping the Controller . . . . . . . . . . . . . . . . . . . . . 1-15
Step 11: Configure the GuardPLC Controller’s IP
Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
Step 12: Recover from a Controller Fault After Using
the Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17
Configure the Programming Terminal . . . . . . . . . . . . . . . . 1-19
Specify the Host SRS . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19
Login Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20
Determine the IP Address and SRS of the Controller . . . . . . 1-21
Change the SRS of the Controller . . . . . . . . . . . . . . . . . . . . 1-22
Change the IP Address of the Controller . . . . . . . . . . . . . . 1-23
Chapter 2
Connect to GuardPLC Distributed
I/O Modules In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Understand Module Addressing . . . . . . . . . . . . . . . . . . . . . 2-1
Module Default Settings . . . . . . . . . . . . . . . . . . . . . . . . 2-1
SRS (System.Rack.Slot) . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Add the Module to the Hardware Configuration . . . . . . . . . 2-2
Configure the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3