Orion System VCM-X/RNE Operator Interfaces - Manual (Page 38)

VCM-X / RNE SETPOINTS
VCM-X / RNE Operator Interfaces Technical Guide 38
Setpoints - General Procedures
System Manager Instructions
From any menu screen, press
<SETPOINTS>
. The Unit Selection
Screen will appear requesting that you enter the unit ID number. Enter
the correct unit ID number of the VCM-X Controller you want to change
Setpoints for and press
<ENTER> . You will see the screen shown below.
1) Change Setpoint
2) Configure Unit
3) Damper Force
ESC) Exit Menu
Enter <1> on the keypad to display the fi rst unit Setpoint screen.
Modular Service Tool Instructions
From any menu screen, press <SETPOINTS> . The Unit Selection
Screen will appear requesting that you enter the unit ID number. Enter
the correct unit ID number of the VCM-X or RNE Controller you
want to change Setpoints for and press
<ENTER>
. You will then see
Setpoint Screen #1.
Setpoint Screen Index
The available Setpoint Screens for the VCM-X or RNE Controller are
listed on the next few pages by sequential screen number. When each
VCM-X or RNE Controller is confi gured for the fi rst time, it is best to
start with screen #1 and proceed to each Setpoint Screen in numerical
order until you have viewed all available Setpoint Screens. This ensures
that you have seen all of the available VCM-X or RNE Controller
Setpoint possibilities and have the opportunity to change or accept the
defaults for each screen. Once the unit Setpoints are confi gured and you
decide to change one of the screen options, it is helpful to know what
screen number contains the confi guration you wish to change. With
this in mind, the following is a list of all the VCM-X or RNE Setpoint
Screens in numerical order with a brief listing of the Setpoint feature
available on each screen:
Setpoint Screen #1 HVAC Mode Setpoints
Setpoint Screen #2 HVAC Mode Select Deadband
Setpoint Screen #3 Unoccupied Setbacks
Setpoint Screen #4 SAT Cooling Setpoints
Setpoint Screen #5 Cool Reset Source Setpoints
Setpoint Screen #6 SAT Heating Setpoints
Setpoint Screen #7 Heat Reset Source Setpoints
Setpoint Screen #8 Stage Control Window
Setpoint Screen #9 Outdoor Air Lockouts
Setpoint Screen #10 Cutoff Temperatures Lo SAT
& Hi SAT
Setpoint Screen #11 Minimum Supply Fan VFD Speed
For Heating
VCM-X / RNE Setpoint Screen Index
Setpoint Screen #12 Morning Warm-up Target Temp &
Max Length
Setpoint Screen #13 Dehumidifi cation Indoor RH & OA
Dewpoint
Setpoint Screen #14 Dehumidifi cation Coil Temperature
Setpoint Screen #15 Cooling Head Pressure Setpoint
(VCM-X Modular/VCM-X WSHP/
RNE)
Setpoint Screen #16 Reheat Head Pressure Setpoint
(VCM-X Modular/VCM-X WSHP/
RNE)
Setpoint Screen #17 Economizer Setpoints OAT/WB Enable
Setpoint Screen #18 Economizer Setpoints Min Position &
Control Rate
Setpoint Screen #19 Outdoor Air CFM Min & Max Control
Setpoint Screen #20 Outdoor Air CFM Deadband
Setpoint Screen #21 Maximum Economizer Position if High
CO
2
Level Occurs
Setpoint Screen #22 CO
2
Protection Limit Max Level &
Reset Range
Setpoint Screen #23 Static Setpoint, Deadband & Control
Rate
Setpoint Screen #24 Building Pressure Setpoint & Deadband
Setpoint Screen #25 Return Air Bypass Damper Factor
Setpoint
Setpoint Screen #26 Fan Starting Delay Timer
Setpoint Screen #27 Mechanical Heat Cool Failures Occur
After No Change For
Setpoint Screen #28 Preheat/Low Ambient Temperature
Setpoint Screen #29 Max OA Damper Tempering Limit
Setpoint Screen #30 HVAC Schedule
Setpoint Screen #31 Push-Button Override Duration
Setpoint Screen #32 HVAC Mode Sensor Slide Offset
Setpoint Screen #33 Heat Pump Auxiliary Heating Delay
Setpoint Screen #34 Heat Pump Defrost Temp and
Defrost Timer (VCM-X Modular/RNE)
Setpoint Screen #35 Adaptive Defrost Adjustment
(VCM-X Modular/RNE)
Setpoint Screen #36 Heat Wheel Defrost
Setpoint Screen #37 Internal Schedule Optimal Start Soak
Multiplier
Setpoint Screen #38 Trend Log Interval
Setpoint Screen #39 Sensor Calibration For SPC & SAT
Setpoint Screen #40 Sensor Calibration For RAT & OAT
Setpoint Screen #41 Sensor Calibration For Coil