Orion System VCM-X/RNE Operator Interfaces - Manual (Page 78)

INDEX
VCM-X / RNE Operator Interfaces Technical Guide 78
S
SCREENS, continued
Duct Static Pressure Screen.........19,29
Economizer Control Screen.........20,30
Economizer Maximum Position if High CO
2
Level
Setpoint.........43
Economizer Minimum Position & Control Rate
Setpoints.........43
Economizer OAT/WB Enable Setpoint.........43
Economizer Overrides.........69
Emergency Shutdown Input.........25,34
Energy Saving Screen.........14
Exhaust VFD Override.........69
Full Digital Module.........22
Head Pressure Module.........22,32
Head Pressure Setpoint Cooling.........42
Head Pressure Setpoint Reheat.........42
Heat During Dehumidify Screen.........20,30
Heat Pump Auxiliary Heating Delay.........46
Heat Pump Control.........24,34
Heat Pump Defrost Setpoints.........46
Heat Reset Source.........40
Heat Wheel Defrost Setpoint.........47
Holiday Schedule.........17
HVAC Mode Enable Screen.........19,29
HVAC Mode Select Deadband Setpoints.........39
HVAC Mode Sensor Slide Offset Setpoint.........46
HVAC Mode Setpoints.........39
HVAC Reset Source.........19,29
HVAC Schedule Setpoint.........45
Indoor Humidity Sensor Screen.........20,30
Initialization for Modular Service Tool.........13
Initialization Screen.........10
Internal Schedule Optimal Start Soak Multiplier
Setpoint.........47
Loop Search Screen.........11
Max OA Damper Tempering Limit.........45
Mechanical Heat/Cool Failure Time Period
Setpoints.........45
MiniLink PD Confi guration.........66
Minimum Supply Fan VFD Speed for Heating
Setpoint.........41
Mod Cooling Override.........70
Mod Heating Override.........70
Modulating Cooling/Heating Screen.........21,31
Modulating Cooling Output Signal.........21
Modulating Cooling Proportional Window
Screen.........22,32
Modulating Cooling Reverse Acting Screens.........22,32
Modulating Cooling Type.........31
Modulating Heating Output Signal Screen.........21,31
Modulating Heating Proportional Window
Screen.........21,31
Modulating Heating Reverse Acting Screen.........21,31
Monitor Outdoor Air CFM.........23,32
Monitor Return Air CFM.........23,33
Monitor Supply Air CFM.........23,33
Morning Warm Up Temp Setpoint.........41
Outdoor Air CFM Deadband Setpoint.........43
Outdoor Air CFM Setpoint.........43
Outdoor Air Cooling & Heating Lockouts Set-
points.........41
Outdoor Duct/Damper Size.........23,32
Outdoor Humidity Sensor Screen.........20,30
Outputs Force Screen.........69
Overrides Screen.........12,14
Preheat/Low Ambient Temperature Setpoint.........45
Proof of Flow Input Screen.........21,31
Push-Button Override Duration Setpoint.........46
RA Bypass Override.........70
RA Damper Override.........70
Relay Confi guration Screens.........27,37
Relay Overrides.........69
Return Air Bypass Control Screens.........25,34
Return Air Bypass Damper Factor Setpoint.........44
Return Duct/Damper Size.........23,33
Reversing Valve Active During Heat/Cool.........24,34
RNE Confi guration Screens.........29
RNE Status Screens.........49
RNE Tonnage.........32
SAT Cooling Setpoints.........39
Schedule Override.........17
Sensor Calibration for COIL.........47
Sensor Calibration for RAT & OAT.........47
Sensor Calibration for SPC & SAT.........47
Set Time & Date Screens.........15
Space Sensor Overrides Screen.........12
Split Condenser.........22
Stage Control Window Setpoints.........41
Static Setpoint, Deadband & Control Rate
Setpoints.........44
Supply Duct/Damper Size.........23,33
Supply Fan Cycle Screen.........19,29
Supply Fan Starting Delay Timer Setpoint.........45
Supply VFD Override.........69
Trend Log Interval Setpoint.........47
Unit Selection Screens.........9,29
Unoccupied Cooling & Heating Setbacks
Setpoints.........39
Uses R410A.........26,36
VAV/Zone Box Confi guration.........58
VAV/Zone Confi guration.........58
VAV/Zone Controller Setpoints.........60
VAV/Zone Damper Operation.........58
VAV/Zone Status.........64
VCM-X Confi guration Screens.........19
VCM-X / RNE Controller Status Screens.........49