Rockwell Automation 1771-QDC, D17716.5.87(Passport) CLAMP AND EJECT MODE - Manual (Page 70)

Select Command and Status Bits
to Sequence Machine Operation
Chapter 6
6-3
Table 6.C
Command Bits for Automatic Functions in Clamp and Eject Mode
To initiate this
profile/movement:
Toggle this bit: Or the profile/movement
starts automatically after:
If this bit is
Reset:
1st Clamp Close DYC02ĆB00 - -
2nd Clamp Close DYC02ĆB01 1st Clamp Close CPC03ĆB08
3rd Clamp Close DYC02ĆB02 2nd Clamp Close CPC03ĆB09
Low Pressure Close DYC02ĆB03 3rd Clamp Close CPC03ĆB10
1st Clamp Open DYC02ĆB10 - -
2nd Clamp Open DYC02ĆB11 1st Clamp Open OPC03ĆB08
3rd Clamp Open DYC02ĆB12 2nd Clamp Open OPC03ĆB09
Clamp Open Slow DYC02ĆB13 3rd Clamp Open OPC03ĆB10
First Ejector
Advance
DYC02ĆB14 On Clamp Position During
Open
EPC03ĆB08 and
EPC03ĆB09
Ejector Continue DYC03ĆB15 Previous Ejector Stroke EPC03ĆB12
Table 6.D
Status and Command Bit Interaction for Automatic Functions
in Clamp and Eject Mode
For this
Profile/Movement:
During Execution
this bit is:
At Completion
this bit is:
At completion
If this Then this
command bit is: status bit is:
SET RESET SET RESET also SET also SET
1st Clamp Close SYS21ĆB00 SYS02ĆB00 SYS02ĆB00 SYS21ĆB00 CPC03ĆB08 SYS22ĆB00
2nd Clamp Close SYS21ĆB01 SYS02ĆB01 SYS02ĆB01 SYS21ĆB01 CPC03ĆB09 SYS22ĆB01
3rd Clamp Close SYS21ĆB02 SYS02ĆB02 SYS02ĆB02 SYS21ĆB02 CPC03ĆB10 SYS22ĆB02
Low Pressure Close SYS21ĆB03 SYS02ĆB03 SYS02ĆB03 SYS21ĆB03 --- SYS22ĆB03
1st Clamp Open SYS21ĆB10 SYS02ĆB10 SYS02ĆB10 SYS21ĆB10 OPC03ĆB08 SYS22ĆB10
2nd Clamp Open SYS21ĆB11 SYS02ĆB11 SYS02ĆB11 SYS21ĆB11 OPC03ĆB09 SYS22ĆB11
3rd Clamp Open SYS21ĆB12 SYS02ĆB12 SYS02ĆB12 SYS21ĆB12 OPC03ĆB10 SYS22ĆB12
Clamp Open Slow SYS21ĆB13 SYS02ĆB13 SYS02ĆB13 SYS21ĆB13 --- SYS22ĆB13
Ejector Advance SYS21ĆB14 SYS02ĆB14 SYS21ĆB14 SYS02ĆB14 EPC03ĆB12 SYS22ĆB14
Intermediate Ejector
Retract
SYS21ĆB14 SYS02ĆB14 SYS21ĆB14 SYS02ĆB14 EPC03ĆB12 SYS22ĆB15
Final Ejector Retract SYS21ĆB14 SYS02ĆB14 SYS02ĆB14 SYS21ĆB14 --- SYS22ĆB15