Winco DGC-2020 - Manual (Page 62)

4-12 DGC-2020 BESTCOMSPlus Software 9400200990 Rev B
A
Enable ECU Support: Check box to enable ECU support.
B
Enable DTC Support: Check box to enable DTC support.
C
CANBus Address: Accepts an address number from 0 to 253 in increments of 1.
D
ECU Config: Standard, Volvo Penta, or MTU MDEC.
E
Speed Select: Primary or Secondary.
F
Accelerator Position: Adjustable from 0 to 100% in 1% increments.
G
Select MDEC module type: Can Module 201, 302, 303, or 304.
H
MDEC speed demand switch: Analog CAN, Analog ECU, Up Down ECU, Up Down Can, Frequency, or
No CAN Demand.
I
MDEC engine RPM request: Adjustable from 1,400 to 2,000 in increments of 1.
J Output Select: Fuel Contact or Pre-start Contact.
K Pulsing: Enable or Disable.
L
Engine Shutdown: Adjustable from 1 to 60 s in 1 s increments.
M
Pulse Cycle Time: Adjustable from 1 to 60 s in 1 s increments.
N
Settling Time: Adjustable from 5,500 to 30,000 ms in 1 ms increments.
O
Response Timeout: Adjustable from 1 to 60 s in 1 s increments.
Modem Setup (Optional)
DGC-2020 controllers with style number xxxxxMxxx are equipped with an internal telephone modem that
has dial-in and dial-out capability. The modem gives the DGC-2020 the ability to dial up to four telephone
numbers
A
and annunciate user-selected conditions to specified pagers
B
. These user-selected conditions
include
C
:
• Auxiliary Input 1 Closed • ECU Low Coolant Level Alarm
• Auxiliary Input 2 Closed • Emergency Stop Alarm
• Auxiliary Input 3 Closed • High Coolant Temp Pre-Alarm
• Auxiliary Input 4 Closed • kW
Overload Pre-Alarm
• Auxiliary Input 5 Closed • Loss of ECU Coms Alarm
• Auxiliary Input 6 Closed • Loss of Generator Voltage Sensing Alarm
• Auxiliary Input 7 Closed • Low Battery Voltage Pre-Alarm
• Auxiliary Input 8 Closed • Low Coolant Temp Pre-Alarm
• Auxiliary Input 9 Closed • Low Fuel Alarm
• Auxiliary Input 10 Closed • Low Fuel Pre-Alarm
• Auxiliary Input 11 Closed • Low Oil Pressure Alarm
• Auxiliary Input 12 Closed • Low Oil Pressure Pre-Alarm
• Auxiliary Input 13 Closed • MPU Speed Sender Fail Alarm
• Auxiliary Input 14 Closed • Oil Pressure Sender Fail Alarm
• Auxiliary Input 15 Closed • Overcrank
Alarm
• Auxiliary Input 16 Closed • Overspeed
Alarm
• Battery Overvoltage Pre-Alarm • Scheduled Maintenance Pre-Alarm
• Coolant Temp Sender Fail Alarm • Switch Not in Auto
• Cooldown Timer Active • Weak Battery Voltage Pre-Alarm
Dial-Out
The DGC-2020 uses telelocator alphanumeric protocol (TAP) version 1.7 when communicating with
paging companies. This data format
D
specifies seven data bits with even parity. If required, eight data bits
with no parity may be specified.
The message string sent by the DGC-2020 can be limited to a length supported by the receiving pagers
E
.
If a message to be transmitted by the DGC-2020 exceeds the pager message limit, the DGC-2020 will
make multiple calls to transmit the complete message.
Dial-out messages are sent by the DGC-2020 at a user-defined interval
F
. This interval gives an operator
the opportunity to dial into the DGC-2020. A second user-defined interval
G
determines how frequently
dial-out attempts are made following a dial-out failure.
Dial-In
When the DGC-2020 modem shares a line used for voice communication, the number of rings H required
for the modem to answer can be increased to allow time for an operator to answer an incoming telephone
call.