FEC AFC1500 User Manual
Page 13
7.2.2 Real-time display indication mode.
7-5
7.2.3 Fastening results display mode.
7-6
7.2.4 Parameter display mode
7-7
7.2.5 Parameter Data List
7-9
7.2.6 Status Display
7-22
7.3 Download / Setup Mode Operation.
7-23
7.3.1 Download Mode selection
7-23
7.3.2 Setup Mode selection
7-24
7.3.3 Parameter # Selection.
7-25
7.3.4 Data # selection
7-26
7.3.5 Data Edit Mode Operation
7-27
7.3.6 Parameter Copy
7-28
7.3.7 I/O Enable (Stand Alone or Multi Configuration)
7-29
7.3.8 Dual Transducer Set-up
7-30
Chapter 8: Maintenance and Inspection
8-1
8.1 Inspection Items
8-2
8.1.1 Nutrunner (Tool)
8-2
8.1.2 Spindle Assembly
8-2
8.1.3 Homerun cables
8-2
8.1.4 SAN unit
8-3
8.1.5 Air Handling Units (Air Conditioner, Heat Exchanger, etc.)
8-3
8.2 Basic operational tests
8-4
8.2.1 Torque transducer.
8-4
8.2.2 Resolver.
8-4
8.2.3 Motor.
8-4
8.2.4 Transmission Disassembly and Inspection
8-6
8.3 Replacements
8-9
8.3.1 SAN Unit Replacement
8-9
8.3.2 Replace Nutrunner (tool)
8-10
8.3.3 Replace Homerun cables
8-10
Chapter 9: Troubleshooting
9-1
9.1 Abnormal Conditions.
9-2
9.2 Torque Transducer Origin Error, Cal Check Error.
9-3
9.2.1 Code 1-0 Torque transducer / Zero Voltage error.
9-3
9.2.2 Code 1-1 Torque transducer / Cal Voltage error.
9-3
9.2.3 Code 1-2 Torque transducer / Zero check error.
9-3
9.2.4 Code 1-3 Torque transducer / Cal self-check error.
9-4
9.2.5 Code 1-4 Torque transducer / Started on Zero condition error.
9-4
9.2.6 Code 1-5 Torque transducer / Started on Cal condition error
9-4
9.2.7 Code 1-6 Torque transducer / Zero Level Self Check Error
9-4
9.3 Torque Over Abnormals
9-5
9.3.1 Code 2-0 Torque Over Abnormal / Offset Torque
9-5
9.3.2 Code 2-1 Torque Over Abnormal / Torque Inhibit High Limit
9-5
9.4 Tool EEPROM Errors
9-6
9.4.1 Code 3-0 Preamplifier / Tool ID Checksum error
9-6
9.4.2 Code 3-1 Preamplifier / Tool type error
9-6
9.4.3 Code 3-2 Preamplifier / Started without tool connected
9-6
9.4.4 Code 3-3 Preamplifier / Tool is not connected
9-6
9.5 System Memory Errors
9-7
9.5.1 Code 4-0 system memory error / Flash ROM write error
9-7
9.5.2 Code 4-1 system memory error / Flash ROM read error
9-7
9.5.3 Code 4-2 system memory error / Servo Amp Flash ROM error
9-7
9.6 Servo Amplifier Response / Resolver
9-8