FEC AFC1500 - Manual (Page 173)

AFC1500 Operations Manual Appendix A (Rev. 5: 02/08)
Appendix A-3
AFC1500 Data Parameter Setting Blank Form
ITEM DATA SETTING PARM D- No DATA
System
0 00 TORQUE UNIT #.
0 01 ROM VERSION (Not adjustable)
0 02 AMPLIFIER VERSION (Not adjustable)
0 03 FASTENING FUNCTION VERSION(Standalone/Multi)
0 04 External Gear Ratio
Tool Data
0 10 TOOL # (not adjustable)
0 11 TOOL CAL TORQUE.
Factory Set 0 12 CAL. VOLTAGE
0 13 ZERO TORQUE VOLTAGE
0 14~1A FEC In House Management Data
0 1B / 1C TOOL FASTENING COUNT (1 ST 4 DIGITS / LAST 4 DIGITS)
Tool Type 0 20 TOOL MODEL #
Time Setup
(SAN3-DPx ONLY)
0 30 YEAR “YYYY” EX. “2009”
0 31 MONTH & DATE “mmdd” EX. “0923” (SEPT. 23)
0 32 HOUR & MINUTE “hhmm” EX. “1759” 17:59
0 33 SECONDS “ss” EX. “55” 55 SECONDS
Torque
1~16 00 FASTENING MODE (METHOD + STEPS)
1~16 10 CALIBRATION TORQUE
1~16 11 PEAK TORQUE LOW LIMIT
1~16 12 PEAK TORQUE HIGH LIMIT
1~16 13 STANDARD (STD) TORQUE
1~16 14 SPEED CHANGE TORQUE
1~16 15 1ST TORQUE
1~16 16 SNUG TORQUE
1~16 17 THRESHOLD (THR) TORQUE
1~16 18 CROSSOVER (CROS) TORQUE
1~16 19 TORQUE INHIBIT LIMIT
1~16 1A OFFSET TORQUE LIMIT/1 PULSE REVERSE LIMIT
1~16 1B BREAKAWAY TORQUE LIMIT
1~16 1C FINAL TORQUE LOW LIMIT
1~16 1D FINAL TORQUE HIGH LIMIT
1~16 1E 2ND RATE START TORQUE
Angle
1~16 20 ANGLE LOW LIMIT
1~16 21 ANGLE HIGH LIMIT
1~16 22 STANDARD (STD) ANGLE
1~16 23 1ST ANGLE
1~16 24 CROSSOVER ANGLE
1~16 25 ANGLE CORRECTION
1~16 26 2ND RATE START ANGLE (NOT USED)
1~16 27 3RD RATE START ANGLE (NOT USED)
Rate
1~16 30 1ST RATE LOW LIMIT
1~16 31 1ST RATE HIGH LIMIT
1~16 32 2ND RATE LOW LIMIT
1~16 33 2ND RATE HIGH LIMIT
1~16 34 3RD RATE HIGH LIMIT
1~16 35 3RD RATE HIGH LIMIT
Time
1~16 40 INITIAL TIME
1~16 41 1ST TIME HIGH LIMIT
1~16 42 FINAL TIME HIGH LIMIT
1~16 43 FIRST TIME LOW LIMIT
1~16 44 FINAL TIME LOW LIMIT
1~16 45 RAMP UP TIME
1~16 46 RAMP DOWN TIME
1~16 47 REVERSE RAMP UP TIME
1~16 48 TORQUE RECOVERY TIME
Speed
1~16 50 INITIAL SPEED
1~16 51 FREE RUN SPEED
1~16 52 SLOW DOWN SPEED
1~16 53 TORQUE SPEED
1~16 54 REVERSE 1,2 SPEED
1~16 55 REVERSE 3 / OR 1 PULSE REVERSE SPEED
1~16 56 OFFSET CHECK SPEED
Revolutions 1~16 60 FREE RUN REVOLUTIONS
1~16 61 TORQUE INHIBIT REVOLUTIONS
1~16 62 OFFSET CHECK REVOLUTIONS
1~16 63 REVERSE 2 REVOLUTIONS
1~16 64 REVERSE 3 REVS. / OR 1 PULSE REV. TIME
1~16 68 RUNDOWN REVOLUTIONS LOW LIMIT
1~16 69 RUNDOWN REVOLUTIONS HIGH LIMIT
Current 1~16 70 FULL SCALE CURRENT VALUE
1~16 71 HIGH CURRENT LIMIT
1~16 72 LOW CURRENT LIMIT
1~16 73 FASTENING CURRENT LIMIT