FEC DSP1500 (SAN3) User Manual
Page 56
enFORCE
DSP1500 SAN Unit Operation Manual
(Rev. 4)
PAGE 4－16
Chapter 4: System Setup and Wiring
WORK SELECT 0 thru 4: Parameter Select signal (Normally Open)
These 5 inputs [WORK SELECT 0-4] form a binary code which is capable of selecting
up to 32 different sets of press parameters.
*Allow at least 10ms from the time this signal is turned on before turning on the START signal.
Do not turn this signal off at least until BUSY goes “HIGH”.
WORK
SELECT 4
WORK
SELECT 3
WORK
SELECT 2
WORK
SELECT 1
WORK
SELECT 0
Param
No.
MANUAL mode
OFF (OPEN) OFF (OPEN) OFF (OPEN) OFF (OPEN) OFF (OPEN)
1
H o m e - p o s i t i o n s e a r c h
OFF (OPEN) OFF (OPEN) OFF (OPEN) OFF (OPEN)
ON
2
H o m e - p o s i t i o n r e t u r n
OFF (OPEN) OFF (OPEN) OFF (OPEN)
ON
OFF (OPEN)
3
A d v a n c e h i g h s p e e d j o g
OFF (OPEN) OFF (OPEN) OFF (OPEN)
ON
ON
4
R e t u r n h i g h s p e e d jo g
OFF (OPEN) OFF (OPEN)
ON
OFF (OPEN) OFF (OPEN)
5
Advance middle speed jog
OFF (OPEN) OFF (OPEN)
ON
OFF (OPEN)
ON
6
R etu rn mi ddl e speed j og
OFF (OPEN) OFF (OPEN)
ON
ON
OFF (OPEN)
7
A dv a nc e l ow s p e e d j o g
OFF (OPEN) OFF (OPEN)
ON
ON
ON
8
R e t u r n l o w s p e e d j o g
OFF (OPEN)
ON
OFF (OPEN) OFF (OPEN) OFF (OPEN)
9
OFF (OPEN)
ON
OFF (OPEN) OFF (OPEN)
ON
10
OFF (OPEN)
ON
OFF (OPEN)
ON
OFF (OPEN)
11
OFF (OPEN)
ON
OFF (OPEN)
ON
ON
12
OFF (OPEN)
ON
ON
OFF (OPEN) OFF (OPEN)
13
OFF (OPEN)
ON
ON
OFF (OPEN)
ON
14
OFF
(OPEN)
ON ON ON
OFF
(OPEN)
15
OFF
(OPEN)
ON ON ON ON
16
ON
OFF (OPEN) OFF (OPEN) OFF (OPEN) OFF (OPEN)
17
ON
OFF (OPEN) OFF (OPEN) OFF (OPEN)
ON
18
ON
OFF (OPEN) OFF (OPEN)
ON
OFF (OPEN)
19
ON
OFF (OPEN) OFF (OPEN)
ON
ON
20
ON
OFF (OPEN)
ON
OFF (OPEN) OFF (OPEN)
21
ON
OFF (OPEN)
ON
OFF (OPEN)
ON
22
ON OFF
(OPEN) ON
ON OFF
(OPEN)
23
ON OFF
(OPEN) ON
ON
ON 24
ON
ON
OFF (OPEN) OFF (OPEN) OFF (OPEN)
25
ON
ON
OFF (OPEN) OFF (OPEN)
ON
26
ON
ON
OFF (OPEN)
ON
OFF (OPEN)
27
ON ON
OFF
(OPEN)
ON ON
28
ON
ON
ON
OFF (OPEN) OFF (OPEN)
29
ON ON ON
OFF
(OPEN)
ON
30
ON ON ON ON
OFF
(OPEN)
31
ON ON ON ON ON
32
If the start signal is turned “ON” while in MANUAL (JOG) mode, the press will perform the function
defined in the MANUAL operation of the selected Parameter Number; “Home-position search”,
“Home-position return”, “Advance jog” and “Return jog”.
The speed of the operation of MANUAL mode is set in the Data Number 00-32: MANUAL
OPERATION SPEED
System Parameter. (See Page 6-21）The speed of the “Home-position
return” and “High speed jog” is set to this set value.
The speed of the “middle speed jog” is set to 1/10 of this set value or the tool’s minimum speed.
The speed of the “low speed jog” is set to 1/100 of this set value or the tool’s minimum speed.
The speed of Home Position Search is set in the Data Number 00-31 System Parameter.
If a value greater than 10mm/sec. is entered for Home Position Search speed,
the system will limit Home Position Search speed to 10mm/sec.
On a “Home Position Search”, the return operation operates first and when the
CCW limit sensor turns OFF, the operation changes to advance operation. After
the CCW limit sensor turns ON again, the motor will advance until the resolver
location (in pulses) is at 0. This point is set to the zero point and becomes the
home position. (See Section 7.2.3.2)
Н
Н