FEC DSP1500 (SAN3) - Manual (Page 99)

enFORCE
DSP1500 SAN Unit Operation Manual
PAGE 6－23 (Rev 4)
Chapter 6: System Operation
6.4.5.2 Work Parameters: Parameter Number 01 to 32
Item
Parameter No.
PARM
Data No.
D-NO
DATA
Load
０１～３２ ００
Press Mode (Press Method ＋ Judgment Operation ＋ Loading
Direction＋Return Operation)
０１～３２ １０ Calibration Load ［KN/KLBS/METRIC TON］
０１～３２ １１ Final Load High Limit ［KN/KLBS/METRIC TON］
０１～３２ １２ Load Low Limit ［KN/KLBS/METRIC TON］
０１～３２ １３ Load High Limit ［KN/KLBS/METRIC TON］
０１～３２ １４ Target Load ［KN/KLBS/METRIC TON］
０１～３２ １５ Interference Check Load ［KN/KLBS/METRIC TON］
０１～３２ １６ Press Speed 1 Start Load ［KN/KLBS/METRIC TON］
０１～３２ １７ Press Speed 2 Start Load ［KN/KLBS/METRIC TON］
０１～３２ １８ Distance Measurement Start Load ［KN/KLBS/METRIC TON］
０１～３２ １９ Load Change / Load Rate Change ［KN/KLBS/METRIC TON］
０１～３２ ２０ Time Start Load ［KN/KLBS/METRIC TON］
０１～３２ ２１ Return Load ［KN/KLBS/METRIC TON］
０１～３２ ２２ Part Check 1 Load ［KN/KLBS/METRIC TON］
０１～３２ ２３ Part Check 2 Load Low Limit ［KN/KLBS/METRIC TON］
０１～３２ ２４ Part Check 2 Load High Limit ［KN/KLBS/METRIC TON］
０１～３２ ２５ Part Check 3 Load Low Limit ［KN/KLBS/METRIC TON］
０１～３２ ２６ Part Check 3 Load High Limit ［KN/KLBS/METRIC TON］
Distance
０１～３２ ３０ Final Distance High Limit ［mm］
０１～３２ ３１ Distance Low Limit ［mm］
０１～３２ ３２ Distance High Limit ［mm］
０１～３２ ３３ Target Distance ［mm］
０１～３２ ３４ Judgment Load Detection Point ［mm］
０１～３２ ３５ Approach Distance ［mm］
０１～３２ ３６ Interference Check Distance ［mm］
０１～３２ ３７ Press Speed 1 Start Distance ［mm］
０１～３２ ３８ Press Speed 2 Start Distance ［mm］
０１～３２ ３９ Detection Start Distance ［mm］
０１～３２ ４０ Detection End Distance ［mm］
０１～３２ ４１ Job Start Distance ［mm］
０１～３２ ４２ Part Check 1 Distance Low Limit ［mm］
０１～３２ ４３ Part Check 1 Distance High Limit ［mm］
０１～３２ ４４ Part Check 2 Start Distance ［mm］
０１～３２ ４５ Part Check 2 End Distance ［mm］
０１～３２ ４６ Part Check 3 Start Distance ［mm］
０１～３２ ４７ Part Check 3 End Distance ［mm］
Advance /
Return
Position
Signal
０１～３２ ５０ Advance Position ON Distance ［mm］
０１～３２ ５１ Advance Position OFF Distance ［mm］
０１～３２ ５２ Return Position ON Distance ［mm］
０１～３２ ５３ Return Position OFF Distance ［mm］
Time
０１～３２ ６０ Slow Start Time [sec]
０１～３２ ６１ Load Hold Time [sec]
０１～３２ ６２ Press Time [sec]
０１～３２ ６３ Press Time Low Limit [sec]
０１～３２ ６４ Press Time High Limit [sec]
０１～３２ ６５ Acceleration Time [sec]
０１～３２ ６６ Deceleration Time [sec]