Yaskawa P7B Drive Bypass - Manual (Page 17)

Physical Installation 1 - 5
Table 1.3 240/230V Enclosure Data
Input
Volts
HP 1
Drive
Model
CIMR-
Bypass 2
Model
Number
NEC
FLA
OL
110%
1 min
Heat 3
Loss
Watts
Enclosure Dimensions 4
NEMA 1 & NEMA 12 -FVFF
H W D
inches
Weight 5
of
Assembly
Enclosure Dimensions w/Add-on 4
NEMA 1 & NEMA 12-FVFF
H W D
inches
Weight 5 of
Assembly
+Add-on
Box
Electrical
Schematic
240
0.5 P7U22P21A P7B_A002 2.2 2.4 68
29.48 19.06 13.66
Dimension Drawing 6
S-5542
115 lbs
43.35 19.06 13.66
Dimension Drawing
S-5543
156 lbs
P7B-00
0.75 P7U22P21A P7B_A003 3.2 3.5 68
1 P7U22P21A P7B_A004 4.0 4.4 78
2 P7U22P21A P7B_A006 6.8 7.5 110
3 P7U22P21A P7B_A009 9.6 10.6 141
5 P7U23P71A P7B_A015 15.2 16.7 202
7.5 P7U25P51A P7B_A022 22.0 24.2 273
10 P7U27P51A P7B_A028 28.0 30.8 365
127 lbs 164 lbs
15 P7U20111A P7B_A042 42.0 46.2 578
20 P7U20151A P7B_A054 54.0 59.4 653
40.48 25.63 14.66
Dimension Drawing 7
S-5544
208 lbs
55.35 25.63 14.66
Dimension Drawing
S-5545
291 lbs
25 P7U20181A P7B_A068 68.0 74.8 746
30 P7U20221A P7B_A080 80.0 88.0 939
221 lbs 307 lbs
40 P7U20301A P7B_A104 104.0 114.4 1340
230
50 P7U20370A P7B_A130 130.0 143.0 1523
84.00 25.63 26.25 8
Dimension Drawing 9
S-5550
847 lbs
NOT REQUIRED
60 P7U20370A P7B_A154 154.0 169.4 1544
943 lbs
75 P7U20450A P7B_A192 192.0 211.2 1860
100 P7U20750A P7B_A248 248.0 272.8 3003 1214 lbs
125 P7U20750A P7B_A312 312.0 343.2 3045 1330 lbs
150 P7U20900A P7B_A360 360.0 396.0 3440 1423 lbs
Note 1: Horsepower rating is based on a standard NEMA B 4-pole motor.
Note 2: The underscore position in these model numbers codes for the enclosure type: V = NEMA1, B = NEMA12 FVFF.
Note 3: Heat loss is the amount of heat dissipated by the drive at full load with all standard options available inside the enclosure. Drive heat sink losses are
included in the heat loss data. Heat loss data is for the enclosure without the add-on enclosure.
Note 4: Height dimension (H) excludes the mounting screw tabs. Depth dimension (D) excludes MCP disconnect handle.
Note 5: This data represents the total weight with all possible standard options. Weight could be less depending on the options specified.
Note 6: All standard options are available in this size enclosure except options E (RFI Filter) and K (5% Output Reactor). Options E and K require the add-on
enclosure.
Note 7: All options are available in this size enclosure except E (RFI Filter), R (3% Line Reactor), and K (5% Output Reactor). Only option E combined with
either option R or option K can be installed in the add-on enclosure. Options R and K together require an increase in the size of the P7 Bypass Enclosure.
Contact the factory if all three options are required. Options D (2 Motor “OR”) or A (2 Motor “AND”) for 30 Hp and 40 Hp require the next size
enclosure.
Note 8: Heat sink mounted externally varies the depth dimension depending on the drive size. Depth will not exceed dimension shown.
Note 9: All options are available in this size enclosure except options D (2 Motor “OR”) or A (2 Motor “AND”) for 75 Hp and 100 Hp require the next size
enclosure.