Yaskawa P7B Drive Bypass - Manual (Page 286)

Index - 6
Operation
Menu ..................................................................3-7, 3-9
Status (U1-12) .........................................................A-26
Operator Programming Errors (OPE)..............................6-11
Option
Card Faults .........................................................6-3, 6-4
Communication Error Selection.............................. 5-26
Options (Peripheral Devices) ...........................................E-4
Orientation, Drive........................................................... 1-12
Oscillation
Mechanical .............................................................. 6-18
with PI control......................................................... 6-18
with V/f control ....................................................... 6-18
Output
Current Monitor (U1-03).........................................A-26
Frequency – See Frequency, Output
Ground Fault Detection Selection ...........................A-22
Monitors ....................................................... A-26, A-27
Phase Loss ................................................................. 6-9
Power Monitor (U1-08)...........................................A-26
Power Ratings – See Specifications, Standard Drive
Terminal Status Monitor (U1-11)............................A-26
Transistors (IGBT)
Inspecting ...........................................................7-2
Spare Parts .................................................F-2, F-3
Testing..................................................6-20 to 6-22
Voltage Monitor (U1-06).........................................A-26
Outputs, Analog – See Analog Outputs
Outputs, Digital – See Digital Outputs
Over Current (OC)........................................... 5-6, 5-30, 6-5
Overheat (OH)
Alarms/Faults .....................................................6-9, 6-5
Cooling Fin (Heatsink)...............................6-5, 6-9, C-4
Drive....................................................................... A-22
Motor........................................................6-5, 6-9, A-19
Parameters .................................................... A-19, A-22
Pre-Alarm........................................................6-9, A-22
Overload
Alarms/Faults ...................................................5-30, 6-6
Capacity..................................................................... C-4
Drive.......................................................................... 6-6
Motor............................................................... 6-6, A-18
Overtorque – See Torque Detection
Protection ....................................................... A-19, C-4
Overtorque – See Torque Detection
Overvoltage Protection......................................6-6, 6-9, C-4
DC Bus – See DC Bus Voltage
P
Parameters
Accel/Decel (C1-01 – C1-11) ...................................A-7
Analog Inputs (H3-02 – H3-13) ..............................A-16
Analog Outputs (H4-01 – H4-08)................. A-17, A-18
Auto-Tuning (T1-02 – T1-04) ................................ A-25
Capacity Related........................................................B-1
Carrier Freq (C6-02 – C6-05) ................................... A-8
Com OPT Setup (F6-01 – F6-05) ........................... A-11
COPY Function (o3-01 – o3-02) ............................ A-25
DC Braking (b2-01 – b2-09) ....................................A-4
Delay timers (b4-01 – b4-02) ...................................A-5
Digital Inputs (H1-01 – H1-05) ................. A-12 to A-14
Digital Outputs (H2-01 – H2-02) ........................... A-14
Energy Saving (b8-01 – b8-06) ................................ A-7
Example of Changing .....................................3-15, 3-16
Factory Reset (Initialize) ......................................... A-2
Fault Restart (L5-01 – L5-03) .................................A-21
Hdwe Protection (L8-01 – L8-19) .......................... A-22
High Slip (n3-01 – n3-04) ...................................... A-23
Hunting Prevention (n1-01 – n1-02) ...................... A-23
Initialization (A1-00 – A1-05).................................. A-2
Jump Frequencies (d3-01 – d3-04) ........................... A-9
Key Selections (o2-01 – o2-15).................... A-24, A-25
Listing of ..................................................... A-1 to A-29
Modified – See Modified Constants
Monitor Select (o1-01 – o1-08) .................... A-23, A-24
MOP/Trim Control (d4-01 – d4-02) ..........................A-9
Motor Overload (L1-01 – L1-05) ............................A-19
Motor Setup (E2-01 – E2-05) ................................. A-11
PI Control (b5-01 – b5-30) ............................... A-5, A-6
Preset Reference (d1-01 – d1-17) ............................. A-8
Programming ................................................ 5-1 to 5-40
PwrLoss Ridethru (L2-01 – L2-05) ........................ A-19
Ref Detection (L4-01 – L4-06)................................A-21
Reference Limits (d2-01 – d2-03) ............................ A-9
S-Curve Acc/Dec (C2-01 – C2-02) ...........................A-7
Sequence (b1-01 – b1-12)..........................................A-4
Serial Com Setup (H4-06 – H4-08) ........................ A-18
Setting and Reading................................................. 3-13
Speed Search (b3-01 – b3-05) ...................................A-5
Stall Prevention (L3-01 – L3-06) ............................A-20
Torque Comp (C4-01 – C4-02)................................. A-8
Torque Detection (L6-01 – L6-03) ..........................A-21
Troubleshooting .......................................................6-14
User (A2-01 – A2-32)....................................... A-2, A-3
V/f Pattern (E1-01 – E1-13) ....................................A-10
Parity – See Modbus Communications