Yaskawa P7B Drive Bypass - Manual (Page 258)

Specifications C - 4
!
All Voltages
Table C.4 Common Drive Specifications
All Models Specification
Control method
Sine wave PWM
V/f control
Speed range 40:1
Speed control accuracy ±2 to 3% (77
°
F ± 50
°
F) (25
°
C ± 10
°
C)
Frequency accuracy
(temperature characteristics) Digital references: ± 0.01% (14
°
F to 104
°
F) (-10
°
C to +40
°
C)
Analog references: ±0.1% (77
°
F ± 50
°
F) (25
°
C ±10
°
C)
Frequency setting resolution
Digital references: 0.01 Hz
Analog references: 0.025/50 Hz (10 bit with sign)
Frequency setting signal
(Speed Command)
0-10 Vdc, 4-20 mA
Acceleration/Deceleration
time
0.0 to 6000.0 s (2 selectable combinations of independent acceleration and deceleration settings)
Main Drive control
functions
Restarting for momentary power loss, bi-directional speed search, overtorque detection, 5 preset speeds,
acceleration/deceleration time changes, S-curve acceleration, 3-wire sequence, auto-tuning, cooling fan ON/OFF con-
trol, torque compensation, jump frequencies, upper and lower limits for frequency references, DC braking for starting
and stopping, high-slip braking, PI control (with sleep function), energy-saving control, Modbus communications (RS-
485/422, 19.2 kbps maximum), fault reset, and copy function
Main Bypass control
functions
Provides an alternate connection for the motor to line power for operation at full speed only, directly from line power.
Three electrically interlocked IEC rated contactors isolate the Drive when operating in Bypass mode. Control logic cir-
cuit provides Hand/Off/Auto functions and safety circuit interlocks. Includes fused 120VAC control transformer, motor
circuit protector/disconnect, motor overload relay, selector switches and indicating lights.
Motor protection Protection by electronic thermal overload relay
Fuse blown protection Stops for fuse blown
Overload capacity and
maximum current
110% of rated output current for 60 seconds
Overvoltage protection
208-240VAC: Stops when main-circuit DC voltage is above 410 V
480VAC: Stops when main-circuit DC voltage is above 820 V
Undervoltage protection
208-240VAC: Stops when main-circuit DC voltage is below 190 V
480VAC: Stops when main-circuit DC voltage is below 380 V
Momentary power loss
ride thru Power Interuptions of 15 ms or more
By selecting the momentary power loss method, operation can be continued if power is restored within 2 s
Cooling fin overheating Protection by thermistor
Stall prevention Stall prevention during acceleration, deceleration, or running
Grounding protection Protection by electronic circuits. (50% of inverter rated current)
Charge indicator Lit when the main circuit DC voltage is approx. 50 Vdc or more
Enclosure Type
Enclosed wall-mounted type (NEMA 1): CIMR-P7U20P4 thru 2030 and 40P4 thru 4055
Open chassis type (IP00): CIMR-P7U2022 thru 2110 and 4030 thru 4300
Ambient operating
temperature 14
°
F to 104
°
F (-10
°
C to 40
°
C) NEMA 1 type
14
°
F to 113
°
F (–10
°
C to 45
°
C) Open chassis type
Ambient operating humidity 95% max. (with no condensation)
Storage temperature 68
°
F to 140
°
F (- 20
°
C to + 60
°
C) short-term temperature during transportation
Application site Indoor (no corrosive gas, dust, etc.)
Altitude 3300 ft. (1000 m), higher altitudes by derate
Vibration 10 to 20 Hz, 32 ft/sec 2 (9.8 m/s 2 ) max.; 20 to 50 Hz, 6.5 ft/sec 2 (2 m/s 2 ) max.
P
rotectiv
e Fun
ct
ions
Cont
ro
l Char
act
er
is
ti
cs
E
nvi
ronm
en
t