Allied Telesis AT-S63 User Manual
Command line interface user’s guide, Management software
Advertising
Table of contents
Document Outline
- Contents
- Tables
- Preface
- Section I
- Basic Operations
- Chapter 1
- Starting a Command Line Management Session
- Chapter 2
- Basic Command Line Commands
- Chapter 3
- Basic Switch Commands
- Chapter 4
- Enhanced Stacking Commands
- Chapter 5
- Simple Network Time Protocol (SNTP) Commands
- Chapter 6
- SNMPv2 and SNMPv2c Commands
- Chapter 7
- Port Parameter Commands
- ACTIVATE SWITCH PORT
- DISABLE INTERFACE LINKTRAP
- DISABLE SWITCH PORT
- DISABLE SWITCH PORT FLOW
- ENABLE INTERFACE LINKTRAP
- ENABLE SWITCH PORT
- ENABLE SWITCH PORT FLOW
- PURGE SWITCH PORT
- RESET SWITCH PORT
- SET SWITCH PORT
- SET SWITCH PORT FILTERING
- SET SWITCH PORT RATELIMITING
- SHOW INTERFACE
- SHOW SWITCH PORT
- Chapter 8
- Port Statistics Commands
- Chapter 9
- MAC Address Table Commands
- Chapter 10
- Static Port Trunking Commands
- Chapter 11
- LACP Port Trunking Commands
- Chapter 12
- Port Mirroring Commands
- Section II
- Advanced Operations
- Chapter 13
- File System Commands
- Chapter 14
- File Download and Upload Commands
- Chapter 15
- Event Log and Syslog Server Commands
- Chapter 16
- Classifier Commands
- Chapter 17
- Access Control List Commands
- Chapter 18
- Class of Service (CoS) Commands
- Chapter 19
- Quality of Service (QoS) Commands
- ADD QOS FLOWGROUP
- ADD QOS POLICY
- ADD QOS TRAFFICCLASS
- CREATE QOS FLOWGROUP
- CREATE QOS POLICY
- CREATE QOS TRAFFICCLASS
- DELETE QOS FLOWGROUP
- DELETE QOS POLICY
- DELETE QOS TRAFFICCLASS
- DESTROY QOS FLOWGROUP
- DESTROY QOS POLICY
- DESTROY QOS TRAFFICCLASS
- PURGE QOS
- SET QOS FLOWGROUP
- SET QOS POLICY
- SET QOS PORT
- SET QOS TRAFFICCLASS
- SHOW QOS FLOWGROUP
- SHOW QOS POLICY
- SHOW QOS TRAFFICCLASS
- Chapter 20
- Denial of Service Defense Commands
- Section III
- IGMP Snooping, MLD Snooping, and RRP Snooping
- Chapter 21
- IGMP Snooping Commands
- Chapter 22
- MLD Snooping Commands
- Chapter 23
- RRP Snooping Commands
- Section IV
- SNMPv3
- Chapter 24
- SNMPv3 Commands
- ADD SNMPV3 USER
- CREATE SNMPV3 ACCESS
- CREATE SNMPV3 COMMUNITY
- CREATE SNMPV3 GROUP
- CREATE SNMPV3 NOTIFY
- CREATE SNMPV3 TARGETADDR
- CREATE SNMPV3 TARGETPARAMS
- CREATE SNMPV3 VIEW
- DELETE SNMPV3 USER
- DESTROY SNMPv3 ACCESS
- DESTROY SNMPv3 COMMUNITY
- DESTROY SNMPv3 GROUP
- DESTROY SNMPv3 NOTIFY
- DESTROY SNMPv3 TARGETADDR
- DESTROY SNMPv3 TARGETPARMS
- DESTROY SNMPV3 VIEW
- PURGE SNMPV3 ACCESS
- PURGE SNMPV3 COMMUNITY
- PURGE SNMPV3 NOTIFY
- PURGE SNMPV3 TARGETADDR
- PURGE SNMPV3 VIEW
- SET SNMPV3 ACCESS
- SET SNMPV3 COMMUNITY
- SET SNMPV3 GROUP
- SET SNMPV3 NOTIFY
- SET SNMPV3 TARGETADDR
- SET SNMPV3 TARGETPARAMS
- SET SNMPV3 USER
- SET SNMPV3 VIEW
- SHOW SNMPV3 ACCESS
- SHOW SNMPV3 COMMUNITY
- SHOW SNMPv3 GROUP
- SHOW SNMPV3 NOTIFY
- SHOW SNMPV3 TARGETADDR
- SHOW SNMPV3 TARGETPARAMS
- SHOW SNMPV3 USER
- SHOW SNMPV3 VIEW
- Section V
- Spanning Tree Protocols
- Chapter 25
- Spanning Tree Protocol Commands
- Chapter 26
- Rapid Spanning Tree Protocols Commands
- Chapter 27
- Multiple Spanning Tree Protocol Commands
- Section VI
- Virtual LANs
- Chapter 28
- Port-based, Tagged, and Multiple Mode VLAN Commands
- Chapter 29
- GARP VLAN Registration Protocol Commands
- Chapter 30
- Protected Ports VLAN Commands
- Chapter 31
- MAC Address-based VLAN Commands
- Section VII
- Internet Protocol Routing
- Chapter 32
- Internet Protocol Version 4 Packet Routing
- Internet Protocol Version 4 Packet Routing Overview
- Supported Switches
- Routing Interfaces
- Interface Names
- Static Routes
- Routing Information Protocol (RIP)
- Default Routes
- Equal-cost Multi- path (ECMP) Routing
- Routing Table
- Address Resolution Protocol (ARP) Table
- Internet Control Message Protocol (ICMP)
- Routing Interfaces and Management Features
- Local Interface
- AT-9408LC/SP AT-9424T/GB, and AT-9424T/SP Switches
- Routing Command Example
- Non-routing Command Example
- Upgrading from AT-S63 Version 1.3.0 or Earlier
- ADD IP ARP
- ADD IP INTERFACE
- ADD IP RIP
- ADD IP ROUTE
- DELETE IP ARP
- DELETE IP INTERFACE
- DELETE IP RIP
- DELETE IP ROUTE
- DISABLE IP ROUTE MULTIPATH
- ENABLE IP ROUTE MULTIPATH
- PURGE IP
- SET IP ARP
- SET IP ARP TIMEOUT
- SET IP INTERFACE
- SET IP LOCAL INTERFACE
- SET IP RIP
- SET IP ROUTE
- SHOW IP ARP
- SHOW IP COUNTER
- SHOW IP INTERFACE
- SHOW IP RIP COUNTER
- SHOW IP RIP INTERFACE
- SHOW IP ROUTE
- Internet Protocol Version 4 Packet Routing Overview
- Section VIII
- Port Security
- Chapter 33
- MAC Address-based Port Security Commands
- Chapter 34
- 802.1x Port-based Network Access Control Commands
- Section IX
- Management Security
- Chapter 35
- Web Server Commands
- Chapter 36
- Encryption Key Commands
- Chapter 37
- Public Key Infrastructure (PKI) Certificate Commands
- Chapter 38
- Secure Sockets Layer (SSL) Commands
- Chapter 39
- Secure Shell (SSH) Commands
- Chapter 40
- TACACS+ and RADIUS Commands
- Chapter 41
- Management ACL Commands
- Index