Great Plains Electric Clutch Package - Manual (Page 23)

Great Plains Manufacturing, Inc. Update 2S-2600F/SGS Left Hand Drive 19
03/24/2009 195-073M
Install 2S-2600F/SGS LH Clutch
Refer to Figure 27
23. Select two new:
804-061C WASHER MACH 1.50 X 1.00 X 18GA
and one new:
195-349D WING FERT CLUTCH OUTER SPCR TB
Place the washers on the shaft , followed by
the spacer .
24. Select one saved:
195-160H SPKT CLUTCH 40B23T RND BORE
and three sets saved:
802-152C HHCS 1/4-20X2 GR5
804-006C WASHER LOCK SPRING 1/4 PLT
Insert the bolts through the lock washers
and into every other hole in the sprocket. Insert from
the side with the smaller raised hub. Place the
sprocket, bolt face to left, onto shaft
.
If the following parts are not present, re-insert them:
817-111C BSHG FLG 1.26IDX1.41ODX.87L
176-065D CLUTCH FRICTION WASHER
195-222D BRG 7/8 HEX ID X 1.254 OD
With any flanged ends to right, place the bushing
, the friction washer , the bearing and
the sprocket onto shaft .
25. Select one each saved:
808-240C SPKT 40A23X1.813-1.818 BR/6HOL
26. Select the clutch assembled at step 17. Note that
the 195-347D adaptor has alternating smooth
and tapped (threaded)
1 ⁄
4
in holes.
27. Select one new:
195-350D WING FERT CLUTCH INNER SPCR TB
Place spacer onto shaft . Place the clutch
over the spacer, adaptor end to left, and inside
both chains , .
28. Loosely secure the two sprockets to the clutch using
the bolts and washers at the
1 ⁄
4
in threaded
holes of the 195-347D adaptor .
29. Select three sets new:
805-180C PIN ROLL 1/4 X 1 1/2 LG PLT
Drive the roll pins into the sprockets and the
smooth
1 ⁄
4
in holes of the 195-347D adaptor .
Tighten bolts to specification. Re-seat roll pins
as needed.
30. Select one each new:
196-877D BUSHING 1 1/8 ODX7/8 HEX BORE
839-956C KEY 1/4 X 3/16 X 3.80
Insert the bushing into the right end of the clutch
. Align the keyways of the bushing and clutch,
then insert the key .
31. Select two new:
804-061C WASHER MACH 1.50 X 1.00 X 18GA
Place the washers on the shaft .
32. Select one new:
805-180C PIN ROLL 1/4 X 1 1/2 LG PLT
Drive the pin into the right end hole of the shaft
, outside the washers.
33. Route chains ( , ) over the sprockets. Adjust idler
for Drive Type chain to
1 ⁄
2
in (13mm) slack in long-
est chain span. Adjust idler for option jackshaft chain
to
1 ⁄
4
in (6mm) slack in longest chain span.
Figure 27: 2S-2600F/SGS:
Install LH Clutch
28101
21
58
26
50
46
U
D
F
B
L
R
54
46
n
u
109
125 128
136
116
103
138
50
25
22
24
46
24
46 21
24
109
125
128
125 128
21
138
103
116
138 103 116
136 21
136
54
22
25
25 21 54
22
n u
125 128
22
50
50
22
125
26
58
26
54
58
46
21
50
50
21
n u
n
u