Great Plains Electric Clutch Package - Manual (Page 27)

Great Plains Manufacturing, Inc. Update 2S-2600F/SGS Right Hand Drive 23
03/24/2009 195-073M
Install 2S-2600F/SGS RH Clutch
Refer to Figure 35
53. Select one new:
402-025S LOCK COLLAR, 7/8 HEX W/ SET SC
which, if not pre-assembled, each consist of:
1
402-058D COLLAR LOCK 7/8 HEX and
2 801-035C SCREW SET 5/16-18 SKT KP X 3/8
Adjust set screws to clear the collar hex hole.
Place the collar on the left end of the clutch input
shaft . Do not tighten the set screws at this time.
54. Select two new:
804-061C WASHER MACH 1.50 X 1.00 X 18GA
Place two washers on the clutch input shaft .
55. Select the clutch assembled at step 52. Note that
the 195-347D adaptor has alternating smooth
and tapped (threaded)
1 ⁄
4
in holes.
56. Select one each new:
196-877D BUSHING 1 1/8 ODX7/8 HEX BORE
839-956C KEY 1/4 X 3/16 X 3.80
Place bushing inside clutch . Align keyways of
bushing and Ogura clutch . Insert key .
Place the tab end of the clutch on input shaft .
57. Select one new:
195-348D CLUTCH SPACER TUBE
and six (6) new:
804-061C WASHER MACH 1.50 X 1.00 X 18GA
Insert the spacer in the adaptor , followed by
the washers .
58. Select one saved:
808-240C SPKT 40A23X1.813-1.818 BR/6HOL
Place it on the shaft .
59. Select one saved:
195-161H SPKT CLUTCH 40B23T HEX BORE
and three sets saved:
802-551C HHCS 1/4-20X2 1/4 GR5
804-006C WASHER LOCK SPRING 1/4 PLT
60. Loosely secure the two sprockets to the clutch using
the bolts and washers at the threaded holes
of the 195-347D adaptor .
61. Select three new:
805-180C PIN ROLL 1/4 X 1 1/2 LG PLT
Drive the roll pins into the sprockets and the
smooth
1 ⁄
4
in holes of the 195-347D adaptor .
62. Tighten bolts to specification. Re-seat roll pins
as necessary.
63. Select seven (7) new:
804-061C WASHER MACH 1.50 X 1.00 X 18GA
Place all 7 washers on acremeter shaft .
64. Select one new:
805-180C PIN ROLL 1/4 X 1 1/2 LG PLT
Shift the drive shaft and clutch assembly to drill
left (and into both chains), until the mid roll pin hole
appears to the left of the right bearing
. The hex
bore sprocket needs to capture the acremeter shaft
before that occurs. Drive the pin into the shaft
mid hole.
65. Shift the collar , washers and clutch assembly
to drill left. Secure set screws in collar.
50
22
Figure 35: 2S-2600F/SGS:
Install RH Clutch
28109
54
58
26
46
U
D
F
B
L
R
27
46
d
s
b
126
128
110
136
50
23
46
27
60
61
61
27
d
46
46 d
54
22
26
58
26 54
26 54 58
d
23
46
25 22
46
136
d
110
126
128
126 128
22
50
50
22
126
46
46 s
50
d
b
s 50
21
27 46
54