Great Plains Electric Clutch Package - Manual (Page 50)

46 Electric Clutch Package Great Plains Manufacturing, Inc.
195-073M 03/24/2009
Install 3S-3000F/SGS LH Clutch
Refer to Figure 74
24. Select two new:
804-061C WASHER MACH 1.50 X 1.00 X 18GA
Place them on the right end of shaft .
25. Select one new:
195-349D WING FERT CLUTCH OUTER SPCR TB
Place it on the shaft .
26. Select one saved:
195-160H SPKT CLUTCH 40B23T RND BORE
Place the sprocket, smaller raised hub side to drill
left, onto shaft
. If the following are not still inside
sprocket , re-insert them:
817-111C BSHG FLG 1.26IDX1.41ODX.87L
176-065D CLUTCH FRICTION WASHER
195-222D BRG 7/8 HEX ID X 1.254 OD
With any flanged ends to right, place the bushing
, the friction washer , the bearing and
the sprocket onto shaft .
27. Select one saved:
808-240C SPKT 40A23X1.813-1.818 BR/6HOL
and three sets saved:
802-152C HHCS 1/4-20X2 GR5
804-006C WASHER LOCK SPRING 1/4 PLT
Place sprocket on shaft . From drill left, insert
the bolts through the lock washers and into
every other hole in sprocket .
28. Select the clutch assembled at step 17. Note that
the 195-347D adaptor has alternating smooth
and tapped (threaded)
1 ⁄
4
in holes.
29. Select one new:
195-350D WING FERT CLUTCH INNER SPCR TB
Place spacer onto shaft . Place the clutch
over the spacer, adaptor end to left, and inside
both chains , .
30. Loosely secure the two sprockets to the clutch using
the bolts and washers at the
1 ⁄
4
in threaded
holes of the 195-347D adaptor .
31. Select three sets new:
805-180C PIN ROLL 1/4 X 1 1/2 LG PLT
Drive the roll pins into the sprockets and the
smooth
1 ⁄
4
in holes of the 195-347D adaptor .
Tighten bolts to specification. Re-seat roll pins
as needed.
32. Select one each new:
196-877D BUSHING 1 1/8 ODX7/8 HEX BORE
839-956C KEY 1/4 X 3/16 X 3.80
Insert the bushing into the right end of the clutch
. Align the keyways of the bushing and clutch,
then insert the key .
33. Select two new:
804-061C WASHER MACH 1.50 X 1.00 X 18GA
Place them on the shaft .
34. Select one new:
805-180C PIN ROLL 1/4 X 1 1/2 LG PLT
Drive the pin into the right end hole of the shaft
, outside the washers.
35. Route chains ( , ) over the sprockets. Adjust idler
for Drive Type chain to
1 ⁄
2
in (13mm) slack in long-
est chain span. Adjust idler for option jackshaft chain
to
1 ⁄
4
in (6mm) slack in longest chain span.
Figure 74: 3S-3000F/SGS:
Install LH Clutch
28112
21
58
26
50
46
U
D
F
B
L
R
54
46
n
u
109
125
128
136
116
103
138
50
25
22
24
46
21
24
21
109
21
109
138
103
116
138 103 116
136 21
136
125
128
136 21
125 128
109
54
22
25
25 21 54
22
n u
125 128
22
50
50
22
125
26
58
26
54
58
46
21
50
50
21
n u
n
u