FaxBack NET SatisFAXtion 8.6 - Manual - Manual (Page 215)

4 – Appendices NET SatisFAXtion 8.6 Manual 215
(abort the send) and the modem's OK response. For such a modem, setting this
timeout can speed the hang-up process. Default: 1000 .
close_string_timeout_msecs [dword 0–65535]: How long to wait for
response after sending users close string if that string does not contain any '
^ '
characters. Default: 5000 .
command_timeout_msecs [dword 0–65535]: How long to wait for response
for miscellaneous commands such as
ATE0V1 , AT+FCLASS=1 or AT&D2 . Default:
1000 .
dial_mode [string]: Selects “tone” dialing or “pulse” dialing. Defines whether
the driver sends an
ATDT<dial number> or ATDP<dial number> . Format: Either
TONE or PULSE . Default: TONE .
dial_progress_mode [string]: Determines if dial and busy tones are detected.
The driver implements this by sending the
X# modem command depending
upon this value. Format: Comma separated list of DETECT_BUSY_TONE and
DETECT_DIAL_TONE . Default: DETECT_DIAL_TONE, DETECT_BUSY_TONE .
dsr_delta_reset_timeout_msecs [dword 0–65535]: How often to wait
after DSR comes back on before resetting the modem. If a modem is turned off,
this determines how long after it comes back on before the driver resets it.
When a modem is turned off, and thus, drops its DSR modem status, the driver
will immediately report that the modem is
DEFECTIVE . When the modem is
turned back on, the driver immediately notice that DSR is raised, however, the
modem may need several seconds to wake up before any commands are sent
to it. This feature is not able to be implemented when using TAPI. Default:
10000 .
dte_baud_rate [dword 2–115200]: Baud rate for CLASS2 to use to talk to the
modem at all times, unless the
2400_baud_init setting is true in which case the
driver will only use the dte_baud_rate when the modem is in Class1 mode.
There have been cases on slow machines where setting this to a baud rate like
38400 or 57600 reduces the likelihood of send under-run errors occurring.
Setting this to lower than 19200 has the possibility that the UART wont be able
to keep up with the modem modulation throughput due to extra
DLE escaped
characters. Default: 38400 .
dtmf_detection_begin [string]: When the line_type is DTMF_PROMPT , this
command is sent to the modem before answering. It should cause the modem
to go off hook, emit a prompt tone if possible and collect and report received
DTMF digits. This has the same formate rules as the
init_string , plus a /
{ sequence is translated to a DLE ( 0x10 ) character and a /} sequence is
translated to a ETX ( 0x03 ) character. Format: Up to 80 characters. Default:
#CLS=8A .
dtmf_detection_end [string]: This is what needs to be sent to the modem to
get it out of the state that the
dtmf_detection_begin put it in. It is sent by the
driver when either the 6 second interdigit DTMF timeout occurs or the
dtmf_terminate_digits is received. This has the same format rules as
dtmf_detection_begin . Format: Up to 80 characters.
dtmf_digit_count [dword 0–31]: Max number of DTMF digits to receive.
Setting 0 disables this. Default:
0 .
dtmf_terminate_digit [string]: The received DTMF digit that causes the driver
to terminate DTMF digit collection being done by the modem by sending the