Yokogawa 2-Wire Dual Channel Transmitter/Analyzer FLXA21 - Manual (Page 43)

<3. OPERATION OF pH/ORP>
3-1
IM 12A01A02-01E 5th Edition : Oct. 31, 2013-00
3. OPERATION OF pH/ORP
This chapter describes the screen operations of pH/ORP, the object to be measured.
Further details of screen operations can also be found in section 1.2.
10.38
Tag:FLXA21–PH
25.0
4mA 20mA PH1
°C
pH
19 mV
Execute:
Calibration/Wash
HOLD
Temporary output
Setup:
Comissioning
Change language
Start Quick Setup
Execute &Setup
◆Sensor setup
◆Measuremet setup
◆Output setup
◆Error configuration
◆Logbook configuration
◆Advanced setup
◆Display setup
◆Calculated data setup
Comissioning
◆Manual
◆Automatic
◆Sample
Calibration pH
◆Manual
◆Sample
Calibration ORP
◆Zero/Slope
◆Zero/Slope/ITP(3point)
◆Zero/Slope1,2(3point)
pH Manual
◆Zero/Slope
◆Zero/Slope/ITP(3point)
◆Zero/Slope1,2(3point)
pH Automatic
◆pH
◆ORP
◆Temperature
Calibration
Quick setup Seneor setup Date/Time Measurement setup
Temperature settings mA(output)
HART ＞
PH201G ＞
Communication
◆Setting logbook
Logbook configuration
◆Main display
◆Dual display
◆Individual display
◆Trend
◆Auto Return
◆Adjust contrast
◆MONITOR display
Display setup
◆Enter values
Table mA
Change language
Temporary output
HOLD
Setup: Linear ＞
Table ＞
mA(Output)
◆x-axis: Timing
◆Y-axis: Limits
Trend
◆PH1
◆PH2
Individual display
◆Enter values
Buffer table 1
◆Additional text
PH1 display
◆Additional text
Main display
◆Buffer table 1
◆Buffer table 2
◆Buffer table 3
Free programmable
◆Enter values
Matrix
Input 1 impedance: Low ＞
Input 2 impedance: Low ＞
Impedance setup
◆Temperature settings
◆Temp. compensation
◆Calibration settings
◆Impedance settings
◆Concentration
◆Sensor diag. settings
Measurement setup
Compensation: Manual ＞
Reference temp.
pH: Matrix
＞
TC ＞
ORP: TC ＞
Temp. comp.
◆Define heat cycle
Sensor diag. setting
◆pH settings
◆ORP settings
◆rH settings
Cal. settings
◆Zero and Slope units
◆Limits and timing
◆Buffers (select set)
◆Zero/Slope/ITP
◆Auto correct(Zero, Slope)
Cal. set pH
Select buffer set:
Free programmable ＞
Buffers
mA: Output ＞
Simulate ＞
◆Configure Hold
Output setup
◆Settings
◆Tag
◆Passwords
◆Date/Time
◆Communication
◆Factory setup
Advanced setup
Wash contact: Enabled ＞
PH201G setup
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
2.7
3.2 4.6.4 4.1 4.2.1
4.2.2 4.3
5.1
5.3
5.2
5.1.1
5.1.2
5.1.3
5.4
5.5
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.2.7
4.7.1
4.7.2
4.7.3
4.7.4
4.7.5
4.6.1
4.6.2
4.6.3
4.6.4
4.6.5
4.6.6
Figure 3.1 Menu structure of pH/ORP (the number after the item refers to the relevant section)
PH
3