Metalfab SEW Eurodrive MOVIMOT MM..C - Manual (Page 150)

150
Operating Instructions – MOVIMOT® MM03C - MM3XC
12
UL design with connection voltages 380500 VAC
Technical Data of Standard Design
12.2 UL design with connection voltages 380500 V
AC
MOVIMOT
®
type MM 03C-
503-00
MM 05C-
503-00
MM 07C-
503-00
MM 11C-
503-00
MM 15C-
503-00
MM 22C-
503-00
MM 30C-
503-00
MM 3XC-
503-00
Part number 824 115 5 824 116 3 824 117 1 824 118 X 824 119 8 824 120 1 824 121 X 824 180 5
Apparent output power at
V
mains
= 380...500 V
AC
P
rated
1.1 kVA 1.4 kVA 1.8 kVA 2.2 kVA 2.8 kVA 3.8 kVA 5.1 kVA 6.7 kVA
Connection voltages
Permitted range V
mains
3 x 380 V
AC
/ 400 V
AC
/415 V
AC
/460 V
AC
/500 V
AC
V
mains
= 380 V
AC
-10 % ... 500 V
AC
+10 %
Supply frequency f
mains
50 Hz ... 60 Hz
±
10 %
Rated system current
(at V
mains
= 460 V
AC
)
I
mains
1.1 A
AC
1.4 A
AC
1.7 A
AC
2.1 A
AC
3.0 A
AC
4.3 A
AC
5.8 A
AC
7.5 A
AC
Output voltage V
out
0...V
in
Output frequency
Resolution
Operating point f
out
2...100 Hz
0.01 Hz
460 V at 60 Hz
Rated output current I
rated
1.6 A
AC
2.0 A
AC
2.5 A
AC
3.2 A
AC
4.0 A
AC
5.5 A
AC
7.3 A
AC
9.6 A
AC
Motor power P
mot
0.5 HP
0.37 kW
0.75 HP
0.55 kW
1.0 HP
0.75 kW
1.5 HP
1.1 kW
2 HP
1.5 kW
3.0 HP
2.2 kW
5 HP
3.7 kW
5.4 HP
1)
4 kW
1) Only possible with S3 25 % ED
PWM frequency 4 (factory setting) / 8 / 16
2)
kHz
2) 16 kHz PWM frequency (low-noise): When DIP SWITCH S1/7 = ON, the units operate with a 16 kHz PWM frequency (low noise) and
switch back in steps to lower switching frequencies depending on the heat sink temperature.
Current limitation I
max
Motor: 160 % with
ᛴ
Regenerative:160 % with
ᛴ
Maximum motor lead
length 15 m when mounting the MOVIMOT ® frequency inverter close to the motor
(with SEW hybrid cable and option P2.A)
External braking resistor R
min
150
Ω
68
Ω
Interference immunity Meets EN 61800–3
Interference emission Meets EN 61800–3 and class A limit to EN 55011 and EN 55014
Ambient temperature
ϑ
amb
-25 °C...40 °C (P
rated
reduction: 3 % I
N
per K to max. 60 °C) 3)
3) -25 °C...40 °C with S3 25% ED (up to 60 °C with S3 10 % ED)
Climate class 3 K3
Enclosure
(motor-dependent) IP54, IP55, IP65, IP66 (options, specify when ordering)
IP67 (only available for inverters with terminal box)
Operating mode DB (EN 60149-1-1 and 1-3), S3 max. cycle duration 10 minutes
Cooling type (DIN 41 751) Self-cooling
Altitude h
≤
1000 m (P
rated
reduction: 1 % per 100 m starting at an altitude of 1000 m, see also the section
"Electrical Installation – Installation Instructions")
Ext. power supply to elec-
tronics Tl. 24 V V = +24 V
±
25 %, EN 61131-2, residual ripple max. 13 %
I
in
≤
250 mA (typ. 150 mA at 24 V)
Input capacitance 100
µ
F
Three binary inputs Isolated by opto-coupler, PLC-compatible (EN 61131-2)
R
i
≈ 3.0 k Ω , I
in
≈ 10 mA, sampling time ≤ 5 ms
Signal level +13 V...+30 V = "1" = Contact closed
-3 V...+5 V = "0" = Contact open
Control functions Tl. R
Tl. L
Tl. f1/f2 CW/Stop
CCW/Stop
"0" = Setpoint 1 / "1" = Setpoint 2
Output relay
Contact data Tl. K1a
Tl. K1b Response time
≤
15 ms
24 V
DC
/ 0.6 A
DC
/ DC11 to IEC 337-1
Signaling function Normally open contact for ready
signal Contact made:
– with applied voltage (24 V + supply)
– if no fault was detected
– after self-test phase concluded (after switch-on)
Serial interface Tl. RS+
Tl. RS- RS-485
P
i
f
kVA
Hz
n