Yaskawa Z1000U - Manual (Page 365)

No. Name
User
Setting
o1-07 Second Line Monitor Selection
o1-08 Third Line Monitor Selection
o1-09 Frequency Reference Display Units
o1-10 User-Set Display Units Maximum Value
o1-11 User-Set Display Units Decimal Display
o1-13
Frequency Reference and Frequency Related
Monitor Custom Units 1
o1-14
Frequency Reference and Frequency Related
Monitor Custom Units 2
o1-15
Frequency Reference and Frequency Related
Monitor Custom Units 3
o1-16 F1 Key Function Selection
o1-17 F2 Key Function Selection
o1-18 User-Defined Parameter Upper
o1-19 User-Defined Parameter Lower
o2-02 STOP Key Function Selection
o2-03 User Parameter Default Value
o2-04 Drive Model Selection
o2-05 Frequency Reference Setting Method Selection
o2-06
Operation Selection when Digital Operator is
Disconnected
o2-07 Motor Direction at Power Up when Using Operator
o2-19 Selection of Parameter Write during Uv
o3-01 Copy Function Selection
o3-02 Copy Allowed Selection
o4-01 Cumulative Operation Time Setting
o4-02 Cumulative Operation Time Selection
o4-03 Cooling Fan Maintenance Operation Time Setting
o4-05 Capacitor Maintenance Setting
o4-07 DC Bus Pre-charge Relay Maintenance Setting
o4-11 U2, U3 Initialize Selection
o4-12 kWh Monitor Initialization
o4-13 Number of Run Commands Counter Initialization
o4-17 Real Time Clock Setting
o4-19 Power Unit Price
S1-01 Stillness Control Selection
S1-02 Voltage Reduction Rate
S1-03 Voltage Restoration Level
S1-04 Voltage Restoration Complete Level
S1-05 Voltage Restoration Sensitivity Time Constant
S1-06 Voltage Restoration Time Constant at Impact
S2-01 Sequence Timer 1 Start Time
S2-02 Sequence Timer 1 Stop Time
S2-03 Sequence Timer 1 Day Selection
S2-04 Sequence Timer 1 Selection
S2-05 Sequence Timer 1 Reference Source
S2-06 Sequence Timer 2 Start Time
S2-07 Sequence Timer 2 Stop Time
S2-08 Sequence Timer 2 Day Selection
S2-09 Sequence Timer 2 Selection
S2-10 Sequence Timer 2 Reference Source
No. Name
User
Setting
S2-11 Sequence Timer 3 Start Time
S2-12 Sequence Timer 3 Stop Time
S2-13 Sequence Timer 3 Day Selection
S2-14 Sequence Timer 3 Selection
S2-15 Sequence Timer 3 Reference Source
S2-16 Sequence Timer 4 Start Time
S2-17 Sequence Timer 4 Stop Time
S2-18 Sequence Timer 4 Day Selection
S2-19 Sequence Timer 4 Selection
S2-20 Sequence Timer 4 Reference Source
S3-01
Secondary PI Enable Selection
S3-02
Secondary PI User Display
S3-03
Secondary PI Display Digits
S3-04
Secondary PI Unit Selection
S3-05
Secondary PI Setpoint Value
S3-06
Secondary PI Proportional Gain Setting
S3-07
Secondary PI Integral Time Setting
S3-08
Secondary PI Integral Limit Setting
S3-09
Secondary PI Output Upper Limit
S3-10
Secondary PI Output Lower Limit
S3-11
Secondary PI Output Level Selection
S3-12
Secondary PI Disable Mode
S3-13
Secondary PI Low Feedback Detection Level
S3-14
Secondary PI Low Feedback Detection Time
S3-15
Secondary PI High Feedback Level
S3-16
Secondary PI High Feedback Detection Time
S3-17
Secondary PI Feedback Detection Selection
S4-01
BP Auto Transfer on Fault Enable
E.3 User Setting Table
YASKAWA ELECTRIC TOEP C710636 10B Z1000U HVAC MATRIX Drive User Manual 365
E
Quick Reference Sheet