SkyTrak 8042 Service Manual - Manual (Page 55)

General Information and Specifications
2.30 Model 8042, 10042, 10054 Legacy Rev. 10/03
3. Fuel:
In general, use #2 diesel fuel. From November 15 to
March 15, when operating in cooler climates where
ambient (outside air) temperatures are consistently at or
below 32° F (0° C), use a 50/50 mix of #1 and #2 diesel
fuels. Use a good quality diesel fuel and change the fuel
filter regularly. Additives are not necessary.
b. Engine Capacities
1. Engine Oil Capacity:
Crankcase Capacity (4BT3.9 & 4BTA3.9 Engine)
With filter change.................................11 qt (10,4 liters)
Filter Capacity..........................................1 qt (0,9 liters)
Crankcase Capacity (QSB4.5T Engine Only)
With filter change.................................10.5 qt (10 liters)
Filter Capacity...................................0.85 qt (0,80 liters)
2. Cooling System Capacity (w/o heater):
Cooling System Capacity .......................4 gal (15 liters)
Overflow Bottle Capacity .........................3 qt (2,8 liters)
3. Fuel Tank Capacity:
Total Capacity.....................................37 gal (140 liters)
Usable Capacity ..............................35.6 gal (135 liters)
2.6.7 Drive Shaft Splines
IMPORTANT: DO NOT disassemble any of the drive
shafts (refer to Section 5, “Axles, Drive Shafts, Wheels
and Tires,” of this manual for information covering drive
shafts and U-joints). To help ensure optimum performance,
the drive shaft assemblies are specially balanced as a
unit at the factory. When servicing any flange yoke, slip
yoke or drive shaft tube, order a complete assembly.
Refer to the appropriate parts manual for ordering
information.
Respective of the above statement, should it become
necessary to coat the transmission input drive shaft
splines, use molybdenum disulfide grease. Molybdenum
disulfide grease is specifically formulated for this purpose
and is marketed by several manufacturers under various
names, including:
Aldrich Chemical Co., Inc.
Product name: Aldrich MOLYBDENUM (IV) SULFIDE
Catalog Number: 23,484-2
Package Size: 5 g (0.175 oz)
100 g (3.5 oz)
500 g (17.5 oz)
Contact:
Aldrich Chemical Co., Inc.
P.O. Box 335
Milwaukee, WI 53201 USA
Phone: (414) 273-3850
DOW CORNING, INC.
Product name: MOLYKOTE
®
77 Paste
Contact:
Dow Corning Corporate Center
P.O. Box 994
Midland, MI 48686-0994 USA
Phone: (517) 496-4400
2.6.8 General Anti-Corrosion
a. Anti-Corrosion Compound
For general anti-corrosion protection, use a wax film rust
inhibitor that provides a protective film two ten-thousandths
of an inch (0.0002" or 0,00005 mm) thick. One such rust
inhibitor that is specifically formulated for this purpose is
LPS 3. It is marketed by:
LPS Laboratories, Inc.
4647 Hugh Howell Rd.
Tucker, GA 30085-5052
Phone: 1-800-241-8334
Fax: (770) 493-9206
Note: Anti-corrosion protection is especially important in
frame and stabilizer cylinder pin support bores for
protection from corrosion wear.
b. Anti-Corrosion Need Areas
Coat all unplated pins and all bores for cylinder pins,
attachment pivot pins, chain sheave pins, the quick
attach lock pin and all quick attach lock pin bores. On the
boom, coat the fork shaft and unpainted boom slide
pathways.
2.6.9 Electrical
a. Basic Ratings
Battery Rating ....................... 12V DC Negative Ground
Battery Type......................................Maintenance-Free
4BT3.9 & 4BTA3.9 Engine .. 1,000 Cold Cranking Amps
QSB4.5T Engine ........ 850 Cold Cranking Amps (Each)
Battery Series (4BT3.9 & 4BTA3.9 Engine) ....Series 31
Battery Series (QSB4.5T Engine) ...................Series 27
Number of Batteries (4BT3.9 & 4BTA3.9 Engine)... One
Number of Batteries (QSB4.5T Engine).................. Two
Alternator Rating ..............................................65 Amps