Xilinx 1000BASE-X - Manual (Page 176)

176 www.xilinx.com Ethernet 1000BASE-X PCS/PMA or SGMII v9.1
UG155 March 24, 2008
Chapter 12: Constraining the Core R
INST "gmii_data_bus[6].delay_gmii_txd" IDELAY_VALUE = "33";
INST "gmii_data_bus[5].delay_gmii_txd" IDELAY_VALUE = "33";
INST "gmii_data_bus[4].delay_gmii_txd" IDELAY_VALUE = "33";
INST "gmii_data_bus[3].delay_gmii_txd" IDELAY_VALUE = "33";
INST "gmii_data_bus[2].delay_gmii_txd" IDELAY_VALUE = "33";
INST "gmii_data_bus[1].delay_gmii_txd" IDELAY_VALUE = "33";
INST "gmii_data_bus[0].delay_gmii_txd" IDELAY_VALUE = "33";
The value of IDELAY_VALUE for the gmii_tx_clk clock is preconfigured in the example
designs to meet the setup and hold constraints for the example GMII pinout in the
particular device. The setup/hold timing which is achieved after place-and-route is
reported in the datasheet section of the TRCE report (created by the implement script). See
“Understanding Timing Reports for Setup/Hold Timing.”
Understanding Timing Reports for Setup/Hold Timing
Devices Other Than Virtex-4 or Virtex-5
Setup and Hold results for the TBI or GMII input busses for the following devices are
defined in the Data Sheet Report section of the Timing Report: Virtex-II, Virtex-II Pro,
Spartan-3, Spartan-3E, Spartan-3A, Spartan-3AN, and Spartan-3A DSP. The results are self-
explanatory and show an obvious correlation and relationship to
Figure 12-2 and
Figure 12-3 .
The following example shows the GMII report from a Virtex-II device. The implementation
requires 1.531 ns of setup (this is less than the 2 ns required, to allow for slack). The
implementation requires -0.125 ns of hold (this is less than the 0 ns required, to allow for
slack).
Data Sheet report:
-----------------
All values displayed in nanoseconds (ns)
Setup/Hold to clock gmii_tx_clk
------------+------------+------------+------------------+--------+
| Setup to | Hold to | | Clock |
Source | clk (edge) | clk (edge) |Internal Clock(s) | Phase |
------------+------------+------------+------------------+--------+
gmii_tx_en | 1.531(R)| -0.141(R)|gmii_tx_clk_bufg | 0.000|
gmii_tx_er | 1.531(R)| -0.141(R)|gmii_tx_clk_bufg | 0.000|
gmii_txd<0> | 1.531(R)| -0.141(R)|gmii_tx_clk_bufg | 0.000|
gmii_txd<1> | 1.525(R)| -0.135(R)|gmii_tx_clk_bufg | 0.000|
gmii_txd<2> | 1.531(R)| -0.141(R)|gmii_tx_clk_bufg | 0.000|
gmii_txd<3> | 1.525(R)| -0.135(R)|gmii_tx_clk_bufg | 0.000|
gmii_txd<4> | 1.515(R)| -0.125(R)|gmii_tx_clk_bufg | 0.000|
gmii_txd<5> | 1.515(R)| -0.125(R)|gmii_tx_clk_bufg | 0.000|
gmii_txd<6> | 1.520(R)| -0.130(R)|gmii_tx_clk_bufg | 0.000|
gmii_txd<7> | 1.520(R)| -0.130(R)|gmii_tx_clk_bufg | 0.000|
------------+------------+------------+------------------+--------+
Virtex-4 or Virtex-5 Devices
Setup and hold results for the TBI or GMII input busses can be found in the data sheet
report section of the Timing Report. Note that initially, the results do not indicate an
obvious relationship to
Figure 12-2 and Figure 12-3 . The following example shows the
GMII report from a Virtex-4 device.