KEYENCE IG Series - Manual (Page 158)

A-8
Append
ix
IG-E
The judgment
value (P.V.) is dis-
played as "
".
The hold function is used and
the judgment value (P.V.) is
held. Check the hold function setting.
Input the timing input according to the setting.
"5. Hold function" (page 4-20)
The reset input is ON.
Set the reset input to OFF.
Check the wiring of the reset input.
"11. External input" (page 4-33)
The internal mea-
surement value (R.V.)
is displayed as "

HHHH".
The internal measurement
value (R.V.) falls below the
lower limit (-99.999) of display
range.
• Check the setting for shift target value and shift
the display again.
"3-7 Zero Shift Function (Shifting the
Internal Measurement Value (R.V.))"
(page 3-16)
• Redo the calibration.
"4-5 Calibration Function" (page 4-52)
The internal mea-
surement value
(R.V.) is displayed
as "
HHHH".
The internal measurement
value (R.V.) goes beyond the
upper limit (99.999) of display
range.
The key is locked and the but-
ton operation is disabled. Cancel the key lock (Unlock).
"3-9 Key Lock Function" (page 3-21)
The tolerance tuning was per-
formed when the R.V. is
[
].
Perform the tuning when the internal measure-
ment value (R.V.) is displayed with figures (with
the object measured).
"3-6 Setting the Tolerance Setting Value"
(page 3-11)
When the R.V. is [ ], the
zero shift function was used.
Shift the display when the internal measurement
value (R.V.) is displayed (with the object mea-
sured).
"3-7 Zero Shift Function (Shifting the Inter-
nal Measurement Value (R.V.))" (page 3-16)
The SET1 or SET2 value is
incorrect and the correction
using the calibration function
could not be performed.
Perform the calibration within the possible cor-
rection range.
"4-5 Calibration Function" (page 4-52)
The button operation is dis-
abled.
The connected communication unit <DL-RS1A>
read/write setting switch is set to RW.
Set the read/write setting switch to R.
"RS-232C Communication Unit DL-RS1A
User's Manual"
Display Description Corrective actions

LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
 HOLD CALC CHECK
GO
((((
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
(((( HOLD CALC CHECK
GO
((((
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
(((( HOLD CALC CHECK
GO
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
.QE
GO
HOLD CALC CHECK
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
PQW#.
GO
HOLD CALC CHECK
'TT
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
5*K(6
GO
HOLD CALC CHECK
'TT
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
5'6
GO
HOLD CALC CHECK
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
E/.QE
GO
HOLD CALC CHECK