KEYENCE LS-7600 - Manual (Page 123)

5-61
Chapter 5 Function Settings
5
0.0000005inch
0.01mil
0.000000inch
0.000mil
+3.000000inch
+3000.000mil
0.000000inch
0.000mil
+4.000000inch
+4000.000mil
–0.9999995~
+0.9999995inch
–999.9995~
+999.9995mil
–9.999999~
+9.999999~inch
–9999.999~
+9999.999mil
–99.99999~
+99.99999inch
–99999.99~
+99999.99mil
–999.9999~
+999.9999inch
–999999.9~
+999999.9mil
+3.000000inch
+3000.000mil
0.000000inch
0.000mil
+1.000000inch
+1000.000mil
+1.000000inch
+1000.000mil
+0.100000inch
+100.000mil
–0.100000inch
–100.000mil
OFF
OFF OFF
OFF
OFF
OFF OFF
OFF
0.00000inch
0.00mil
+3.00000inch
+3000.00mil
0.00000inch
0.00mil
+4.00000inch
+4000.00mil
+3.00000inch
+3000.00mil
0.00000inch
0.00mil
–1.00000inch
–1000.00mil
+1.00000inch
+1000.00mil
+1.00000inch
+100.00mil
–0.10000inch
–100.00mil
OFF
OFF
OFF
OFF
0.0000inch
0.0mil
+3.0000inch
+3000.0mil
0.0000inch
0.0mil
+4.0000inch
+4000.0mil
+3.0000inch
+3000.0mil
0.0000inch
0.0mil
–1.0000inch
–1000.0mil
+1.0000inch
+1000.0mil
+1.0000inch
+100.0mil
–0.1000inch
–100.0mil
OFF
OFF
OFF
OFF
0.0000000inch
0.0000mil
+0.3000000inch
+300.0000mil
0.00000inch
0.0000mil
+0.4000000inch
+400.0000mil
+0.3000000inch
+30000.00mil
0.0000000mm
0.0000mil
+0.1000000inch
+100.0000mil
+0.1000000inch
+100.0000mil
+0.0100000inch
+10.0000mil
–0.0100000inch
–10.0000mil
H-LMT
L-LMT
H-LMT
L-LMT
HH
LL
HH
LL
HH
LL
HH
LL
GRAPH-H
GRAPH-L
STD + UPPER
STD + LOWER
STD + UPPER
STD + LOWER
STD + UPPER
STD + LOWER
STD + UPPER
STD + LOWER
GRAPH-H
GRAPH-L
A–
+10V
A–
–10V
HH
HI
LO
LL
STAN-
DARD
UPPER
LOWER
Offset
Threshold
Threshold mode
Ref
erence v
alue mode
Default value
Minimum display unit
Setting item
Calibration setting
Output setting
Tolerance
setting
T1-A/B • T2-A/B
Setting range Default value Setting range Default value Setting range Default value Setting range
0.000001inch
0.02mil
0.00005inch
0.05mil
0.0001inch
0.1mil
Option setting
Ref
.
value
Threshold
• Each cell shows minimum display units in the order of inches and mils.
• Each set value in the table will be initialized if the change of the minimum display unit or the change of
display unit is made. Items other than those in the table will not be, however, initialized.
• If the program is initialized, the display unit will be set to mil and the minimum display unit will be set to
0.00005 (mil). The set values will be initialized as well.