Allied Telesis AT-S63 User Manual
Command line user’s guide, Management software
Advertising
Table of contents
Document Outline
- Contents
- Tables
- Preface
- Section I
- Basic Operations
- Chapter 1
- Overview
- Introduction
- AT-S63 Management Software
- Supported Models
- Supported Features
- AT-StackXG Stacking Module
- Maximum Number of Switches in a Stack
- Management Interfaces
- Management Access Methods
- Enhanced Stacking
- Stack Topology
- Discovery Process
- Master and Member Switches
- Active Configuration File
- Module ID Numbers
- Port Numbers in Commands
- MAC Address Tables
- File Systems
- Compact Flash Memory Card Slots
- Stack IP Address
- Upgrading the AT-S63 Management Software
- Powering On a Stack
- Troubleshooting the Discovery Process
- Chapter 2
- Starting a Command Line Management Session
- Chapter 3
- Basic Command Line Commands
- Chapter 4
- Stacking Commands
- Chapter 5
- Basic Stack Commands
- DISABLE TELNET
- ENABLE TELNET
- PING
- RESET SWITCH
- RESET SYSTEM
- RESTART REBOOT
- RESTART SWITCH
- SET ASYN
- SET DATE
- SET PASSWORD MANAGER
- SET PASSWORD OPERATOR
- SET SWITCH CONSOLETIMER
- SET SYSTEM
- SET TELNET INSERTNULL
- SET TIME
- SET USER PASSWORD
- SHOW ASYN
- SHOW CONFIG DYNAMIC
- SHOW CONFIG INFO
- SHOW SWITCH
- SHOW SYSTEM
- SHOW TIME
- Chapter 6
- SNMPv2 and SNMPv2c Commands
- Chapter 7
- Port Parameter Commands
- Chapter 8
- Port Statistics Commands
- Chapter 9
- MAC Address Table Commands
- Chapter 10
- Static Port Trunking Commands
- Chapter 11
- LACP Port Trunking Commands
- Chapter 12
- Port Mirroring Commands
- Section II
- Advanced Operations
- Chapter 13
- File System Commands
- Chapter 14
- File Download and Upload Commands
- Chapter 15
- Event Log and Syslog Client Commands
- Chapter 16
- Class of Service (CoS) Commands
- Section III
- Snooping Protocol
- Chapter 17
- IGMP Snooping Commands
- Section IV
- SNMPv3
- Chapter 18
- SNMPv3 Commands
- ADD SNMPV3 USER
- CREATE SNMPV3 ACCESS
- CREATE SNMPV3 COMMUNITY
- CREATE SNMPV3 GROUP
- CREATE SNMPV3 NOTIFY
- CREATE SNMPV3 TARGETADDR
- CREATE SNMPV3 TARGETPARAMS
- CREATE SNMPV3 VIEW
- DELETE SNMPV3 USER
- DESTROY SNMPv3 ACCESS
- DESTROY SNMPv3 COMMUNITY
- DESTROY SNMPv3 GROUP
- DESTROY SNMPv3 NOTIFY
- DESTROY SNMPv3 TARGETADDR
- DESTROY SNMPv3 TARGETPARMS
- DESTROY SNMPV3 VIEW
- PURGE SNMPV3 ACCESS
- PURGE SNMPV3 COMMUNITY
- PURGE SNMPV3 NOTIFY
- PURGE SNMPV3 TARGETADDR
- PURGE SNMPV3 VIEW
- SET SNMPV3 ACCESS
- SET SNMPV3 COMMUNITY
- SET SNMPV3 GROUP
- SET SNMPV3 NOTIFY
- SET SNMPV3 TARGETADDR
- SET SNMPV3 TARGETPARAMS
- SET SNMPV3 USER
- SET SNMPV3 VIEW
- SHOW SNMPV3 ACCESS
- SHOW SNMPV3 COMMUNITY
- SHOW SNMPv3 GROUP
- SHOW SNMPV3 NOTIFY
- SHOW SNMPV3 TARGETADDR
- SHOW SNMPV3 TARGETPARAMS
- SHOW SNMPV3 USER
- SHOW SNMPV3 VIEW
- Section V
- Spanning Tree Protocols
- Chapter 19
- Spanning Tree Protocol Commands
- Chapter 20
- Rapid Spanning Tree Protocols Commands
- Section VI
- Virtual LANs
- Chapter 21
- Port-based and Tagged VLAN Commands
- Section VII
- Internet Protocol Routing
- Chapter 22
- Internet Protocol Version 4 Packet Routing Commands
- Section VIII
- Port Security
- Chapter 23
- 802.1x Port-based Network Access Control Commands
- Chapter 24
- RADIUS Commands
- Section IX
- Management Security
- Chapter 25
- Web Server Commands
- Index