Rockwell Automation GV3000/SE AC Gen. Purpose & Vector Bookshelf Drive Start-Up and Reference Manual - Manual (Page 227)

Index Index-3
O
OCL, see Outer Control Loop
OIM, see Operator Interface Module
Open-loop regulation, see Volts/Hertz Regulation
Operator Interface Module, 4-3, 4-6, 4-15, 4-42,
4-45, 4-47
Option Port: Communication Loss Response
(P.062), 4-49
Option Port: Network Reference Source
(P.063), 4-49
Option Port: Network Trim Reference Source
(P.064), 4-50
Option Port: Type and Version (P.065), 4-50
Outer control loop (OCL)
block diagram, H-8
description, H-1
Outer Control Loop Feedback Source (U.040), 4-86
Outer Control Loop Integral Gain (U.046), 4-89
Outer Control Loop Lead/Lag Low Frequency
(U.042), 4-87
Outer Control Loop Lead/Lag Ratio (U.043), 4-87
Outer Control Loop Lead/Lag Select (U.041), 4-86
Outer Control Loop Proportional Gain (U.045), 4-88
Outer Control Loop Proportional Trim Enable
(U.048), 4-90
Outer Control Loop Reference Gain (U.044), 4-88
Outer Control Loop Trim Range Percentage
(U.047), 4-89
Output Phase Loss Enable (P.045), 4-39
Output Relay Configuration (P.013), 4-22
Output, analog, see also Terminal Strip Analog
Output Source (P.012)
polarity, 4-21
selection and scaling, 4-21
Overfrequency Limit (H.022), 4-67
Overspeed protection, 4-9
P
P parameters, 4-6 to 4-54
default settings, E-1 to E-3
listed alphabetically, A-1 to A-2
Parameters
configurable, 4-2
default settings, E-1 to E-4
displaying, 4-3
European default settings, E-1 to E-4
First Menu General, 4-6 to 4-10
H, 4-55 to 4-67
Japanese default settings, E-1 to E-4
listed alphabetically, A-1 to A-4
menu structure, 4-2
modifying, 4-3
P, 4-6 to 4-54
password protection, 4-5
Power Module-dependent default values, C-1
to C-2
read only, 4-2
record of user settings, B-1 to B-5
restoring defaults, see Restore Defaults
(P.050)
Second Menu General, 4-11 to 4-90
tunable, 4-2
types, 4-2
U, 4-68 to 4-90
Vector, 4-68 to 4-90
Volts/Hertz, 4-55 to 4-67
Password
accessing Second Menu, see Second Menu
Password
LED, 3-8
preventing parameter modification, see
Programming Disable (P.051)
Power Module Output Amps (P.095), 4-54
Power Module Type (P.099), 4-54
Power Module-dependent parameter default
values, C-1 to C-2
Preset Speed 1 through Preset Speed 8 (P.031 to
P.038), 4-33
Profibus Interface board, 4-7, 4-48, 4-49, 4-50
Program mode, 3-3 to 3-4
Programming Disable (P.051), 4-41
Programming reference, 4-1 to 4-90
R
r parameters
listed alphabetically, A-3 to A-4
Record of user parameter settings, B-1 to B-5
Regulator
selecting, see Volts/Hertz or Vector Regulation
(P.048)
types, H-1
Reliance Electric, getting assistance from, VII
Remote Meter Interface board, 4-1, 4-11, 4-18,
4-23, 4-34, 4-50, 4-54, H-2
Restore Defaults (P.050), 4-41
RMI board, see Remote Meter Interface Board
RMI parameters, A-3 to A-4
Rotor Time Constant / Fast Flux Up (U.021), 4-80
S
S-Curve Enable (P.019), 4-26
SE, VII