Rockwell Automation RECOMM-CNET ControlNet Communications Module - Manual (Page 6)

IV ControlNet Communications Module
Figure 6.1 – Sample I/O Image with All I/O Enabled................................... 6-3
Figure 6.2 – Sample I/O Image with Only Logic/Reference and
Datalink B Enabled ................................................................. 6-4
Figure 6.3 – I/O Messaging......................................................................... 6-8
Figure 6.4 – I/O Messaging (Continued) ..................................................... 6-9
Figure 6.5 – I/O Messaging (Continued) ................................................... 6-10
Figure 6.6 – I/O Messaging (Continued) ................................................... 6-11
Figure 6.7 – Explicit Message Process ..................................................... 6-12
Figure 6.8 – Explicit Messaging ................................................................ 6-13
Figure 6.9 – CIO Get Attributes Scattered Screen.................................... 6-14
Figure 6.10 – CIO Set Attributes Scattered Screen .................................. 6-15
Figure 6.11 – CIO Get Attribute Single Screen ......................................... 6-17
Figure 6.12 – CIO Set Attribute Single Screen ......................................... 6-18
Figure 7.1 – RSLogix 5000: I/O Configuration Selection ............................ 7-2
Figure 7.2 – RSLogix 5000: New Module Selection.................................... 7-3
Figure 7.3 – Select Module Type: 1756-CNB/B Selection .......................... 7-3
Figure 7.4 – Module Properties: Name Selection ....................................... 7-4
Figure 7.5 – Module Properties: Controller-to-Module Behavior Screen .... 7-4
Figure 7.6 – Module Properties: Indentification/Status Screen ................... 7-5
Figure 7.7 – Module Properties: Informational Screen................................ 7-5
Figure 7.8 – RSLogix 5000: I/O Configuration Folder ................................. 7-6
Figure 7.9 – RSLogix 5000: New Module Selection Screen ....................... 7-7
Figure 7.10 – Select Module Type: Generic ControlNet Module Screen .... 7-8
Figure 7.11 – Module Properties: ControlNet Module Parameters ............. 7-9
Figure 7.12 – Module Properties: RPI Selection ......................................... 7-9
Figure 7.13 – Module Properties: My ControlNet...................................... 7-10
Figure 7.14 – RSLogix: Configure Additional Nodes Screen .................... 7-10
Figure 7.15 – RSLogix 5000: Module-Defined Screen.............................. 7-11
Figure 7.16 – Download to the Controller Dialong Box ............................. 7-11
Figure 7.17 – RSLogix: Attention Symbol ................................................. 7-12
Figure 7.18 – RSNetWorx for ControlNet Screen ..................................... 7-13
Figure 7.19 – RSLogix 5000: Example Without Attention Symbol ............ 7-14
Figure 7.20 – RSLogix 5000: Connection Tree Without Attention Symbol 7-15
Figure 7.21 – I/O Messaging..................................................................... 7-17
Figure 7.22 – I/O Messaging (Continued) ................................................. 7-18
Figure 7.23 – Explicit Message Process ................................................... 7-19
Figure 7.24 – Explicit Messaging .............................................................. 7-20
Figure 7.25 – Get_Attributes_Scattered Message Screen........................ 7-21
Figure 7.26 – Set_Attributes_Scattered Message Screen ........................ 7-22
Figure 7.27 – Set_Attribute_Single Message Screen ............................... 7-24
Figure 7.28 – Get_Attributes_Single Message Screen ............................. 7-25
Figure 8.1 – Status Indicators (Location on Drive May Vary)...................... 8-1
Figure 8.2 – VIewing and Clearing Events Using an LCD OIM................... 8-8