Document Outline

• AutoMax‰ Network Communication Option Board For Use With FlexPak‰ 3000 DC Drives and WebPak‰ 3000 DC Drives
  • M/N 915FK0101
• Chapter 1 Introduction
• Chapter 2 Installation
• Chapter 3 Drive Configuration
• Chapter 4 Programming
• Chapter 5 FlexPak 3000 Drives: Original Register Map
• Chapter 6 FlexPak 3000 Drives: Alternate Register Map
• Chapter 7 WebPak 3000 Drives: Register Map
  • Appendix A Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Original Map) A-1
  • Appendix B Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Alternate Map) B-1
  • Appendix C Cross Reference of Parameter Name to Drop and Register (WebPak 3000 Drives) C-1
  • Index Index-1
• List of Figures
• List of Tables
• Chapter 1 Introduction
  • 1.1 Before You Start
  • 1.2 Where to Find Additional Information
    • You must be familiar with the instruction manuals that describe your system. This can include, but is not limited to:
  • 1.3 Getting Assistance from Reliance Electric
  • 1.4 Related Hardware and Software
    • When the Network Option board is installed in a FlexPak 3000 or WebPak 3000 drive, the drive can be used with the hardware and software listed in table 1.1.
    • Table 1.1 - Hardware and Software Options Available for the Network Option Board (Purchased Separately)
      • 45C71
      • 57C430A
      • 55C431
      • 57C435
      • Various
      • 57C380
      • 2CS3000
      • ?
      • 57C404
      • 57C404A
      • 57C404B
      • 57C381
      • 61C127
  • 1.5 AutoMax Network Option Board Description
    • Figure 1.1 - AutoMax Network Communication Option Board
• Chapter 2 Installation
  • 2.1 Installing the Network Option Board
    • Step 1. Turn off, lock out, and tag all incoming power to the drive.
      • Step 2. Loosen the two (2) captive screws on the drive cover. Remove the cover.
      • Step 3. Loosen the captive screw on the carrier. Swing open the carrier. See figure 2.1.
        • Figure 2.1 - Removing Drive Cover
      • Step 4. Remove the screws that attach the carrier shield to the carrier. See figure 2.2.
        • Figure 2.2 - Removing the Carrier Shield
      • Step 5. Remove the connector that attaches the shield ground wire to the drive power supply. Set the shield aside. See figure 2.3.
        • Figure 2.3 - Removing Shield Ground Wire
      • Step 6. Position the Network Option board over the standoffs. Refer to figure 2.4.
        • Figure 2.4 - Installing the Network Communication Option Board
      • Step 7. Secure the Network Option board using three captive screws on the board.
      • Step 8. Plug the option board ribbon cable into the Network Option board.
      • Step 9. Re-attach the carrier shield ground wire to the drive power supply.
      • Step 10. Re-attach the carrier shield to the carrier.
      • Step 11. Close the carrier and fasten it with the captive screw.
      • Step 12. Re-install the drive cover.
  • 2.2 Connecting the Drive to an AutoMax Network
    • Step 1. Stop any application tasks that are running.
      • Step 2. Use the Network Drop Cable (M/N 57C381) to connect to the Communications Passive Tap (M/N57C380).
      • Step 3. If the drop is at the end of the coaxial cable system, it must be terminated. Terminate by connecting a 75-Ohm Terminating Load (M/N 45C71) to the remaining BNC connector on the passive tap.
      • Step 4. Remove the lockout and tag. Apply power to the drive. If a problem is detected during diagnostics, a fault or alarm will occur. See your drive software manual for information on faults and alarms.
        • Figure 2.5 - Connecting a Drive to the AutoMax Network
• Chapter 3 Drive Configuration
  • 3.1 Setting Up the Drive for Network Communication
    • Step 1. Connect the Network Option board to the network using a passive tap. See section 2.2.
      • Step 2. Apply power to the drive.
      • Step 3. Assign a valid AutoMax network drop number to the drive using parameter netw drop number (P.900). You must set this para...
      • Step 4. Set the network connection type using netw connect type (P.910). This defines the scope of data that will be communicate...
      • Step 5. Apply power to the AutoMax rack.
  • 3.2 Selecting a Network Reference Source
    • amx netw ref select (P.911) specifies the source of the speed/torque reference when control source select (P.000) is set to network. You can select either:
  • 3.3 How the Drive Responds to a Loss of Network Communication
    • The Network Option board attempts to remain active on the network at all times, regardless of the control source setting.
    • 3.3.1 Setting NETW COMM LOSS SELECT (P.901) (FlexPak 3000 Drives Only)
      • P.901 = FAULT (0)
      • P.901 = USE LAST REF (1)
        • When netw comm loss select (P.901) is set to use last ref and network communication is lost, the following occurs:
      • P.901 = USE TRMBLK REF (2)
        • When netw comm loss select (P.901) is set to use termblk ref (2) and network communication is lost, the following occurs:
      • P.901 = USE TRMBLK CNTL (3)
• Chapter 4 Programming
  • 4.1 Selecting a Register Map (FlexPak 3000 Drives Only)
  • 4.2 How the Control Source Selection Affects Data Transfers
  • 4.3 About Network Transfer Rates
    • Output data is one of two types:
    • 4.3.1 I/O Update Enable Logic Summary
      • The logic strings shown in figure 4.1 summarize the output and input enable logic described in this chapter.
        • Figure 4.1 - I/O Update Enable Logic Strings
  • 4.4 Setting Up Data Types That Can Be Transferred
    • 1. Initialize the tunable and configurable input data in the dual-port memory of the master’s Network module
    • 2. Delay for an appropriate amount of time to ensure data have been transferred to the drive
    • 3. Set the Tune/Config Input Enable bit to 1.
  • 4.5 Tune/Config Update Synchronization Flag
    • This flag allows the network master application program to track when the drive has updated tunable and configurable inputs. By ...
      • 1. Modifies the tunable and configurable register data in the appropriate network registers.
      • 2. Sets the tune/config input enable flag.
      • 3. Toggles the tune/config update synchronization flag.
      • 4. Monitors the tune/config update synchronization flag loopback bit until it equals the value written in item 3, above.
    • Table 4.1 - Synchronization Flag Register Locations (Alternate and Original Register Maps)
      • Drop_1
      • 0
      • 7
      • Drop_1
      • 32
      • 15
      • Drop_1
      • 32
      • 14
        • Alternative Synchronization Methods
          • The tune/config update synchronization flag applies only to Drop_1. To determine if the drive received data written to other drops, you must use other methods.
  • 4.6 Monitoring Unacceptable Parameter Values
  • 4.7 Timing Requirements
    • For the following actions, the inputs must be set to 0 for at least 600 msec, then set to 1 for at least 600 msec (a 0-to-1 transition):
  • 4.8 Drive Ready Status Bit
  • 4.9 Display of Parameter Values Over the AutoMax Network
    • Table 4.2 - Front Panel Display Compared to Network Displays
      • 273
      • 0, 1, 2
  • 4.10 Parameters That Are Not Accessible Over the AutoMax Network
  • 4.11 Parameters That Are Only Available in the FlexPak Alternate Register Map
  • 4.12 Settings for Analog and Frequency Outputs
• Chapter 5 FlexPak 3000 Drives: Original Register Map
  • 5.1 Accessing the Original Register Map
  • 5.2 Finding Data in the Original Register Map Tables
    • Table 5.1 - Location of Information in the Original Register Map Tables
      • 1
      • Read
      • 5.2
      • 5-2
      • 5.3
      • 5-4
      • Write
      • 5.4
      • 5-6
      • 5.5
      • 5-7
      • 5.6
      • 5-8
      • 2
      • Read
      • 5.7
      • 5-8
      • 5.8
      • 5-8
      • Write
      • 5.9
      • 5-9
      • 5.10
      • 5-10
      • 3
      • Read
      • 5.11
      • 5-11
      • 5.12
      • 5-12
      • Write
      • 5.13
      • 5-12
      • 5.14
      • 5-13
      • 4
      • Read
      • 5.15
      • 5-14
      • 5.16
      • 5-15
      • Write
      • 5.17
      • 5-16
      • 5.18
      • 5-17
    • Table 5.2 - FlexPak 3000 Original Register Map, Drop_1: Master Read Registers, BASIC and FULL Connections. Runtime Signal Data (Drive Output Data) (Continued)
      • 0
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12
      • 13
      • 14
      • 15
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10 to 15
      • 16
      • 17
      • 18
      • 19
      • 20
      • 21
      • 22
      • 23
      • Runtime signal data are updated by the regulator every 5 msec, unless feedback select (P.200) is set to armature volt, in which case the update time is 10 msec.
    • Table 5.3 - FlexPak 3000 Original Register Map, Drop_1: Master Read Registers, BASIC and FULL Connections. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
      • 10
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12
      • 13
      • 14
      • 15
      • 11
      • 12
      • 13
      • 0
      • 1
      • 2
      • 3 to 15
      • 14
      • 15
      • 16
      • 17
      • 18
      • 19
      • 20
      • 21
      • 22
      • 23
      • 24
      • 25
      • 26
      • 27
      • 28
      • 0
      • 8
      • 29
      • 30
      • 31
      • Tunable, configurable, and status data are updated by the regulator approximately every 600 msec.
    • Table 5.4 - FlexPak 3000 Original Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Control/Reference Data (Drive Input Data)
      • 32
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5 to 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12 - 13
      • 14
      • 15
      • 33
      • 34
      • 35
      • 36
      • 37
      • 38 to 39
      • Control/reference data are read by the regulator every 5 msec, unless feedback select (P.200) is set to armature volt, in which case the update time is 10 msec.
    • Table 5.5 - FlexPak 3000 Original Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Tunable Data (Drive Input Data)
      • 40
      • 41
      • 42
      • 43
      • 44
      • 45
      • 46
      • 47
      • 48
      • 49
      • 50
      • 51
      • 52
      • 53
      • 54
      • 55
      • 56
      • 57
      • 58
      • 59
      • 60
      • Tunable data are read by the regulator approximately every 600 msec while Tune/Config Input Enable bit = 1
    • Table 5.6 - FlexPak 3000 Original Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Configurable Data (Drive Input Data)
      • 61
      • 62
      • 63
      • Configurable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1 and the drive is not running or jogging
    • Table 5.7 - FlexPak 3000 Original Register Map, Drop_2: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data)
      • 0
      • 1
      • 2
      • 3 to 10
      • Runtime signal data are updated by the regulator every 5 msec, unless feedback select (P.200) is set to armature volt, in which case the update time is 10 msec.
    • Table 5.8 - FlexPak 3000 Original Register Map, Drop_2: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
      • 11
      • 12
      • 13
      • 14
      • 15
      • 16
      • 17
      • 18
      • 19
      • 20
      • 21
      • 22
      • 23
      • 24
      • 25
      • 26
      • 27
      • 28
      • 29
      • 30
      • 31
      • Tunable, configurable, and status data are updated by the regulator approximately every 600 msec.
    • Table 5.9 - FlexPak 3000 Original Register Map, Drop_2: Master Write Registers, FULL Connection. Tunable Data (Drive Input Data) (Continued)
      • 32
      • 33
      • 34
      • 35
      • 36
      • 37
      • 38
      • 39
      • 40
      • 41
      • 42
      • 43
      • 44
      • 45
      • 46
      • 47
      • 48
      • 49
      • 50
      • 51
      • 52
      • 53
      • 54
      • 55
      • Tunable data are updated by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1.
    • Table 5.10 - FlexPak 3000 Original Register Map, Drop_2: Master Write Registers, FULL Connection. Configurable Data (Drive Input Data) (Continued)
      • 56
      • 57
      • 58
      • 59
      • 60
      • 61
      • 62
      • 63
      • Configurable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1 and the drive is not running or jogging.
    • Table 5.11 - FlexPak 3000 Original Register Map, Drop_3: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data)
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6 to 11
      • Runtime signal data are updated by the regulator every 5 msec, unless feedback select (P.200) is set to armature volt, in which case the update time is 10 msec.
    • Table 5.12 - FlexPak 3000 Original Register Map, Drop_3: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
      • 12
      • 13
      • 14
      • 15
      • 16
      • 17
      • 18
      • 19
      • 20
      • 21
      • 22
      • 23
      • 24
      • 25
      • 26
      • 27
      • 28
      • 29
      • 30
      • 31
      • Tunable, configurable, and status data are updated by the regulator approximately every 600 msec.
    • Table 5.13 - FlexPak 3000 Original Register Map, Drop_3: Master Write Registers, FULL Connection. Tunable Data (Drive Input Data) (Continued)
      • 32
      • 33
      • 34
      • 35
      • 36
      • 37
      • 38
      • 39
      • 40
      • 41
      • 42
      • 43
      • 44
      • 45
      • 46
      • 47
      • 48
      • 49
      • 50 to 53
      • Tunable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1.
    • Table 5.14 - FlexPak 3000 Original Register Map, Drop_3: Master Write Registers, FULL Connection. Configurable Data (Drive Input Data)
      • 54
      • 55
      • 56
      • 57
      • 58
      • 59
      • 60
      • 61
      • 62
      • 63
      • Configurable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1 and the drive is not running or jogging.
    • Table 5.15 - FlexPak 3000 Original Register Map, Drop_4: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data)
      • 0
      • 0
      • 1
      • 2
      • 3
      • 4
      • 1
      • 2
      • 3
      • 4 to 20
      • Runtime signal data are updated by the regulator every 5 msec, unless feedback select (P.200) is set to armature volt, in which case the update time is 10 msec.
    • Table 5.16 - FlexPak 3000 Original Register Map, Drop_4: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
      • 21
      • 0
      • 1
      • 22
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10 - 15
      • 23
      • 24
      • 25
      • 26
      • 27
      • 28
      • 29
      • 30
      • 31
      • Tunable, configurable and status data are updated by the regulator approximately every 600 msec.
    • Table 5.17 - FlexPak 3000 Drop_4: Master Write Registers, FULL Connection. Tunable Data (Drive Input Data)
      • 32
      • 33
      • 34
      • 35
      • 36
      • 37
      • 38
      • 39
      • 40
      • 41
      • 42
      • 43
      • 44
      • 45
      • 46
      • 47
      • Tunable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1.
    • Table 5.18 - FlexPak 3000 Original Register Map, Drop_4: Master Write Registers, FULL Connection. Configurable Data (Drive Input Data)
      • 48
      • 49
      • 50
      • 0
      • 1
      • 51
      • 52
      • 53
      • 54
      • 55
      • 56
      • 57
      • 58
      • 59
      • 60
      • 61
      • 62
      • 63
      • Configurable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1 and the drive is not running or jogging.
• Chapter 6 FlexPak 3000 Drives: Alternate Register Map
  • 6.1 Accessing the Alternate Register Map
  • 6.2 Diagnosing Processing Errors
    • Table 6.1 - Error Processing Parameters Reported by Group
      • 004
      • 005
      • 211
      • 213
      • 213
      • 214
      • 808
      • 808
      • 809
      • 424
      • 424
      • 423
      • 900
      • 900
      • 910
      • 427
      • 427
      • 426
      • 902
      • 902
      • 903
      • 904
      • 510
      • 510
      • 516
      • 25200
      • 25200
      • 514
      • 514
      • 515
      • 26015
      • 519
      • 519
      • 520
  • 6.3 Finding Data in the Alternate Register Map Tables
    • The alternate register maps in table 6.3 through table 6.18 describe the registers and bits used by the FlexPak 3000 drive on the AutoMax network when netw register map sel (P.914) is set to alternate.
    • Drop_2, Drop_3, and Drop_4 do not have master write registers for control/reference data. Drop_4 does not have a master read register for runtime signal data.
    • Table 6.2 - Location of Information in the FlexPak 3000 Alternate Register Map Tables
      • 1
      • Read
      • 6.3
      • 6-5
      • 6.4
      • 6-7
      • Write
      • 6.5
      • 6-9
      • 6.6
      • 6-10
      • 6.7
      • 6-10
      • 2
      • Read
      • 6.8
      • 6-11
      • 6.9
      • 6-11
      • Write
      • 6.10
      • 6-12
      • 6.11
      • 6-13
      • 3
      • Read
      • 6.12
      • 6-14
      • 6.13
      • 6-14
      • Write
      • 6.14
      • 6-15
      • 6.15
      • 6-16
      • 4
      • Read
      • 6.16
      • 6-17
      • Write
      • 6.17
      • 6-18
      • 6.18
      • 6-18
    • Table 6.3 - FlexPak 3000 Alternate Register Map, Drop_1: Master Read Registers, BASIC and FULL Connections. Runtime Signal Data (Drive Output Data) (Continued)
      • 0
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12
      • 13 - 15
      • 1
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12
      • 1 (con’t.)
      • 13
      • 14
      • 15
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10 to 15
      • 16
      • 17
      • 18
      • 19
      • 20
      • 21
      • 22
      • 23
      • Runtime signal data are updated by the regulator every 5 msec, unless feedback select (P.200) is set to armature volt, in which case the update time is 10 msec.
    • Table 6.4 - FlexPak 3000 Alternate Register Map, Drop_1: Master Read Registers, BASIC and FULL Connections. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
      • 10
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12
      • 13
      • 14
      • 15
      • 11
      • 12
      • 13
      • 0
      • 1
      • 2
      • 3 to 15
      • 14
      • 15
      • 16 to 23
      • 24 to 25
      • 26
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10 - 15
      • 27
      • 28
      • 0
      • 8
      • 29 to 30
      • 31
      • Tunable, configurable, and status data are updated by the regulator approximately every 600 msec.
    • Table 6.5 - FlexPak 3000 Alternate Register Map, Drop_1: Master Write Registers BASIC and FULL Connections. Control/Reference Data (Drive Input Data)
      • 32
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12 & 13
      • 14
      • 15
      • 33
      • 34
      • 35
      • 36
      • 37
      • 38
      • 39
      • Control/reference data are read by the regulator every 5 msec, unless feedback select (P.200) is set to armature volt, in which case the update time is 10 msec.
    • Table 6.6 - FlexPak 3000 Alternate Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Tunable Data (Drive Input Data)
      • 40
      • 41
      • 42
      • 43
      • 44
      • 45
      • 46
      • 47
      • 48
      • 49
      • 50
      • 51
      • 52
      • 53
      • 54
      • 55
      • 56
      • 57
      • 58
      • 59
      • 60
      • Tunable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1.
    • Table 6.7 - FlexPak 3000 Alternate Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Configurable Data (Drive Input Data)
      • 61
      • 62
      • 63
      • Configurable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1 and the drive is not running or jogging.
    • Table 6.8 - FlexPak 3000 Alternate Register Map, Drop_2: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data)
      • 0
      • Runtime signal data are updated by the regulator every 5 msec, unless feedback select (P.200) is set to armature volt, in which case the update time is 10 msec.
    • Table 6.9 - FlexPak 3000 Alternate Register Map, Drop_2: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12
      • 13
      • 14
      • 15
      • 16
      • 17
      • 18
      • 19
      • 20
      • 21
      • 22
      • 23
      • 24
      • 25
      • 26
      • 27
      • 28
      • 29
      • 30
      • 31
      • Tunable, configurable, and status data are updated by the regulator approximately every 600 msec.
    • Table 6.10 - FlexPak 3000 Alternate Register Map, Drop_2: Master Write Registers, FULL Connection. Tunable Data (Drive Input Data) (Continued)
      • 33
      • 34
      • 35
      • 36
      • 37
      • 38
      • 39
      • 40
      • 41
      • 42
      • 43
      • 44
      • 45
      • 46
      • 47
      • 48
      • 49
      • 50
      • 51
      • 52
      • 53
      • 54
      • 55
      • Tunable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1.
    • Table 6.11 - FlexPak 3000 Alternate Register Map, Drop_2: Master Write Registers, FULL Connection. Configurable Data (Drive Input Data) (Continued)
      • 32
      • 56
      • 57
      • 58
      • 59
      • 60
      • 61
      • 62
      • 63
      • Configurable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1 and the drive is not running or jogging.
    • Table 6.12 - FlexPak 3000 Alternate Register Map, Drop_3: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data)
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • Runtime signal data are updated by the regulator every 5 msec, unless feedback select (P.200) is set to armature volt, in which case the update time is 10 msec.
    • Table 6.13 - FlexPak 3000 Alternate Register Map, Drop_3: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
      • 6
      • 7
      • 8
      • 9 to 11
      • 12
      • 13
      • 14
      • 15
      • 16
      • 17
      • 18
      • 19
      • 20
      • 21
      • 22
      • 23
      • 24
      • 25
      • 26
      • 27
      • 28
      • 29
      • 30
      • 31
      • Tunable, configurable, and status data are updated by the regulator approximately every 600 msec.
    • Table 6.14 - FlexPak 3000 Alternate Register Map, Drop_3: Master Write Registers, FULL Connection. Tunable Data (Drive Input Data) (Continued)
      • 33
      • 34
      • 35
      • 36
      • 37
      • 38
      • 39
      • 40
      • 41
      • 42
      • 43
      • 44
      • 45
      • 46
      • 47
      • 48
      • 49
      • 52
    • Table 6.15 - FlexPak 3000 Alternate Register Map, Drop_3: Master Write Registers, FULL Connection. Configurable Data (Drive Input Data) (Continued)
      • 50
      • 51
      • 53
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6 to 15
      • 54
      • 55
      • 56
      • 57
      • 58
      • 59
      • 60
      • 61
      • 62
      • 63
      • Configurable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1 and the drive is not running or jogging.
    • Table 6.16 - FlexPak 3000 Alternate Register Map, Drop_4: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data)
      • 23
      • 24
      • 25
      • 26
      • 27
      • 28
      • 29
      • 30
      • 31
      • Tunable, configurable, and status data are updated by the regulator approximately every 600 msec.
    • Table 6.17 - FlexPak 3000 Alternate Register Map, Drop_4: Master Write Registers FULL Connection. Tunable Data (Drive Input Data),
      • 32
      • 33
      • 34
      • 35
      • 36
      • 37
      • 38
      • 39
      • 40
      • 41
      • 42
      • 43
      • 44
      • 45
      • 46
      • Tunable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1
    • Table 6.18 - FlexPak 3000 Alternate Register Map, Drop_4: Master Write Registers, FULL Connection. Configurable Data (Drive Input Data) (Continued)
      • 47
      • 48
      • 49
      • 50
      • 0
      • 1
      • 51
      • 52
      • 53
      • 54
      • 55
      • 56
      • 57
      • 58
      • 59
      • 60
      • 61
      • 62
      • 63
      • Configurable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1 and the drive is not running or jogging.
• Chapter 7 WebPak 3000 Drives: Register Map
  • 7.1 Using Indirect Parameters
    • Example Using the ISR Word
    • 7.1.1 Enabling the AutoMax Indirect Parameter Numbers
      • Step 1. The tune/config input enable flag must have been cleared for a minimum of 600 msec (Drop_1, register 32, bit 14).
        • Step 2. Modify AutoMax Indirect Register numbers (Drop_2, registers 32 to 63) with the parameter numbers that you wish to write to in the corresponding Drop_3 register. Parameter number 0 deactivates that particular indirect register.
        • Step 3. Modify the corresponding register values (Drop_3, registers 32 to 63) for the parameters selected in step 2.
        • Step 4. Set the tune/config input enable flag (Drop_1, register 32, bit 14).
        • Step 5. Toggle the tune/config update synchronization flag (Drop_1, register 32, bit 15).
        • Step 6. Monitor the tune/config update synchronization flag loopback bit in the Indirect Register Status word (Drop_3, register 32, bit 15) until it equals the value written in step 4.
    • 7.1.2 Changing the AutoMax Indirect Register Values
      • Step 1. Modify the desired register values (Drop_3, registers 32 to63).
        • Step 2. Toggle the tune/config update synchronization flag (Drop_1, register 32, bit 15).
        • Step 3. Monitor the tune/config update synchronization flag loopback bit in the Indirect Register Status word (Drop_3, register 32, bit 15) until it equals the value written in step 4.
    • 7.1.3 Disabling the AutoMax Indirect Registers
      • Step 1. Clear the tune/config input enable flag (Drop_1, register 32, bit 14).
        • Step 2. Toggle the tune/config update synchronization flag (Drop_1, register 32, bit 15).
        • Step 3. Monitor the tune/config update synchronization flag loopback bit in the Indirect Register Status word (Drop_3, register 32, bit 15) until it equals the value written in step 4.
  • 7.2 Diagnosing Processing Errors
    • Table 7.1 - Error Processing Parameters Reported by Group
      • 004
      • 519
      • 519
      • 520
      • 005
      • 213
      • 213
      • 214
      • 014
      • 014
      • 001
      • 002
      • 018
      • 013
      • 900
      • 900
      • 910
      • 424
      • 424
      • 423
      • 902
      • 902
      • 903
      • 904
      • 427
      • 427
      • 426
      • 25200
      • 25200
      • 510
      • 510
      • 516
      • 26015
      • 514
      • 514
      • 515
  • 7.3 Finding Data in the Register Map Tables
    • Table 7.2 - Location of Information in the WebPak Register Map Tables
      • 1
      • Read
      • 7.3
      • 7-5
      • 7.4
      • 7-7
      • Write
      • 7.5
      • 7-8
      • 7.6
      • 7-9
      • 7.7
      • 7-11
      • 2
      • Read
      • 7.8
      • 7-11
      • 7.9
      • 7-12
      • Write
      • 7.10
      • 7-13
      • 3
      • Read
      • 7.11
      • 7-15
      • Write
      • 7.11
      • 7-16
    • Table 7.3 - WebPak 3000 Register Map, Drop_1: Master Read Registers, BASIC and FULL Connections. Runtime Signal Data (Drive Output Data) (Continued)
      • 0
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12
      • 13
      • 14
      • 15
      • 1
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12
      • 13
      • 14
      • 15
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11 to 16
      • 17
      • 18
      • 19
      • 20
      • 21
      • 22
      • 23
      • 24
      • 25
      • Runtime signal data are updated by the regulator every 10 msec.
    • Table 7.4 - WebPak 3000 Register Map, Drop_1: Master Read Registers, BASIC and FULL Connections. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
      • 11
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12
      • 13
      • 14
      • 15
      • 12
      • 13
      • 14
      • 0
      • 1
      • 2
      • 3 to15
      • 15
      • 16
      • 17 to 25
      • 26
      • 27
      • 28
      • 29
      • 30
      • 31
      • Tunable, configurable, and status data are updated by the regulator approximately every 600 msec.
    • Table 7.5 - WebPak 3000 Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Control/Reference Data (Drive Input Data) (Continued)
      • 32
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12
      • 13
      • 14
      • 15
      • 33
      • 34
      • 35
      • 36
      • 37
      • 38
      • 39
      • Control/reference data are read by the regulator every 10 msec.
    • Table 7.6 - WebPak 3000 Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Tunable Data (Drive Input Data)
      • 40
      • 41
      • 42
      • 43
      • 44
      • 45
      • 46
      • 47
      • 48
      • 49
      • 50
      • 51
      • 52
      • 53
      • 54
      • 55
      • 56
      • 57
      • 58
      • 59
      • 60
      • Tunable data are read by the regulator approximately every 600 msec while Tune/Config Input Enable bit = 1.
    • Table 7.7 - WebPak 3000 Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Configurable Data (Drive Input Data)
      • 61
      • 62
      • 63
      • Configurable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1 and the drive is not running or jogging.
    • Table 7.8 - WebPak 3000 Register Map, Drop_2: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data)
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12
      • 13
      • 14
      • Runtime signal data are updated by the regulator every 10 msec.
    • Table 7.9 - WebPak 3000 Register Map, Drop_2: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data)
      • 15
      • 16
      • 17
      • 18
      • 19
      • 20
      • 21
      • 22
      • 23
      • 24
      • 25
      • 26
      • 27
      • 28
      • 29
      • 30
      • 31
      • Tunable, configurable, and status data are updated by the regulator approximately every 600 msec.
    • Table 7.10 - WebPak 3000 Register Map, Drop_2: Master Write Registers, FULL Connection. Tunable Data (Drive Input Data) (Continued)
      • 32
      • 33
      • 34
      • 35
      • 36
      • 37
      • 38
      • 39
      • 40
      • 41
      • 42
      • 43
      • 44
      • 45
      • 46
      • 47
      • 48
      • 49
      • 50
      • 51
      • 52
      • 53
      • 54
      • 55
      • 56
      • 57
      • 58
      • 59
      • 60
      • 61
      • 62
      • 63
      • Tunable data are updated by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1.
    • Table 7.11 - WebPak 3000 Register Map, Drop_3: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data) (Continued)
      • 0
      • 1
      • 2
      • 3
      • 4
      • 5
      • 6
      • 7
      • 8
      • 9
      • 10
      • 11
      • 12
      • 13
      • 14
      • 15
      • 16
      • 17
      • 18
      • 19
      • 20
      • 21
      • 22
      • 23
      • 24
      • 25
      • 26
      • 27
      • 28
      • 29
      • 30
      • 31
      • 0 to 6
      • 7 to 12
      • 13
      • 14
      • 15
      • Runtime signal data are updated by the regulator every 10 msec.
    • Table 7.12 - WebPak 3000 Register Map, Drop_3: Master Write Registers, FULL Connection. Tunable/Configurable Data (Drive Input Data) (Continued)
      • 32
      • 33
      • 34
      • 35
      • 36
      • 37
      • 38
      • 39
      • 40
      • 41
      • 42
      • 43
      • 44
      • 45
      • 46
      • 47
      • 48
      • 49
      • 50
      • 51
      • 52
      • 53
      • 54
      • 55
      • 56
      • 57
      • 58
      • 59
      • 60
      • 61
      • 62
      • Configurable data are read by the regulator approximately every 600 msec when Tune/Config Input Enable bit = 1 and the drive is not running or jogging.
• Appendix A Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Original Map)
  • Table A.1 - Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Original Map) (Continued)
    • 1
    • 10
    • 0
    • 1
    • 23
    • 4
    • 26
    • 1
    • 13
    • 2
    • 1
    • 13
    • 1
    • 1
    • 16
    • 1
    • 40
    • 1
    • 0
    • 8
    • 1
    • 13
    • 1
    • 32
    • 9
    • 1
    • 32
    • 10
    • 1
    • 30
    • 1
    • 63
    • 1
    • 16
    • 2
    • 0
    • 1
    • 17
    • 2
    • 2
    • 3
    • 0
    • 3
    • 16
    • 3
    • 40
    • 3
    • 17
    • 3
    • 41
    • 2
    • 19
    • 2
    • 41
    • 2
    • 18
    • 2
    • 63
    • 2
    • 20
    • 2
    • 42
    • 1
    • 18
    • 4
    • 1
    • 4
    • 33
    • 4
    • 51
    • 4
    • 32
    • 1
    • 19
    • 4
    • 2
    • 4
    • 35
    • 4
    • 34
    • 2
    • 22
    • 2
    • 44
    • 2
    • 23
    • 2
    • 45
    • 4
    • 45
    • 4
    • 52
    • 4
    • 53
    • 4
    • 46
    • 4
    • 54
    • 3
    • 18
    • 3
    • 61
    • 3
    • 19
    • 3
    • 42
    • 3
    • 20
    • 3
    • 43
    • 3
    • 31
    • 1
    • 10
    • 9
    • 1
    • 5
    • 2
    • 27
    • 2
    • 48
    • 2
    • 28
    • 2
    • 49
    • 2
    • 21
    • 3
    • 54
    • 1
    • 6
    • 1
    • 10
    • 6
    • 3
    • 30
    • 3
    • 49
    • 1
    • 26
    • 1
    • 51
    • 1
    • 25
    • 1
    • 50
    • 1
    • 27
    • 1
    • 52
    • 3
    • 3
    • 1
    • 0
    • 10
    • 4
    • 22
    • 8
    • 4
    • 22
    • 5
    • 1
    • 15
    • 1
    • 10
    • 5
    • 1
    • 56
    • 3
    • 24
    • 4
    • 22
    • 3
    • 1
    • 0
    • 11
    • 4
    • 22
    • 7
    • 1
    • 17
    • 1
    • 41
    • 4
    • 50
    • 0
    • 4
    • 48
    • 4
    • 50
    • 1
    • 4
    • 49
    • 1
    • 0
    • 3
    • 1
    • 0
    • 0
    • 1
    • 0
    • 1
    • 1
    • 0
    • 1
    • 0
    • 5
    • 4
    • 27
    • 4
    • 41
    • 1
    • 0
    • 2
    • 1
    • 10
    • 1
    • 32
    • 8
    • 1
    • 32
    • 2
    • 4
    • 22
    • 6
    • 1
    • 61
    • 3
    • 15
    • 3
    • 57
    • 1
    • 10
    • 1
    • 4
    • 29
    • 4
    • 28
    • 4
    • 42
    • 3
    • 33
    • 1
    • 22
    • 3
    • 5
    • 3
    • 56
    • 3
    • 35
    • 3
    • 34
    • 1
    • 37
    • 3
    • 4
    • 1
    • 12
    • 3
    • 36
    • 3
    • 39
    • 3
    • 38
    • 3
    • 37
    • 1
    • 0
    • 4
    • 1
    • 32
    • 4
    • 1
    • 20
    • 4
    • 3
    • 4
    • 56
    • 4
    • 55
    • 4
    • 59
    • 4
    • 57
    • 4
    • 58
    • 4
    • 0
    • 0 - 4
    • 1
    • 10
    • 8
    • 1
    • 0
    • 9
    • 2
    • 56
    • 4
    • 22
    • 2
    • 1
    • 55
    • 3
    • 21
    • 1
    • 32
    • 3
    • 2
    • 15
    • 2
    • 40
    • 4
    • 22
    • 1
    • 1
    • 53
    • 2
    • 14
    • 1
    • 14
    • 4
    • 21
    • 0 & 1
    • 4
    • 37
    • 4
    • 60
    • 4
    • 36
    • 4
    • 39
    • 4
    • 61
    • 4
    • 38
    • 4
    • 22
    • 9
    • 3
    • 12
    • 3
    • 58
    • 1
    • 19
    • 1
    • 43
    • 1
    • 32
    • 11
    • 1
    • 18
    • 1
    • 42
    • 1
    • 13
    • 0
    • 3
    • 55
    • 3
    • 13
    • 3
    • 59
    • 3
    • 14
    • 3
    • 60
    • 1
    • 10
    • 4
    • 2
    • 58
    • 1
    • 21
    • 1
    • 45
    • 1
    • 29
    • 1
    • 57
    • 1
    • 28
    • 1
    • 62
    • 1
    • 34
    • 1
    • 35
    • 1
    • 36
    • 1
    • 58
    • 1
    • 59
    • 1
    • 60
    • 1
    • 10
    • 14
    • 1
    • 7
    • 1
    • 8
    • 1
    • 9
    • 1
    • 33
    • 4
    • 23
    • 4
    • 62
    • 4
    • 24
    • 4
    • 63
    • 2
    • 33
    • 2
    • 60
    • 2
    • 38
    • 2
    • 39
    • 2
    • 37
    • 1
    • 21
    • 2
    • 12
    • 2
    • 52
    • 2
    • 54
    • 2
    • 53
    • 2
    • 51
    • 2
    • 11
    • 2
    • 35
    • 2
    • 34
    • 2
    • 36
    • 2
    • 59
    • 2
    • 55
    • 1
    • 10
    • 13
    • 1
    • 10
    • 7
    • 4
    • 30
    • 4
    • 43
    • 4
    • 31
    • 4
    • 44
    • 1
    • 32
    • 7
    • 1
    • 10
    • 9
    • 1
    • 0
    • 12
    • 4
    • 25
    • 4
    • 40
    • 2
    • 57
    • 1
    • 20
    • 1
    • 44
    • 3
    • 1
    • 3
    • 22
    • 3
    • 62
    • 3
    • 23
    • 3
    • 63
    • 4
    • 22
    • 4
    • 1
    • 31
    • 2
    • 17
    • 2
    • 62
    • 1
    • 32
    • 0
    • 1
    • 46
    • 2
    • 16
    • 1
    • 10
    • 10
    • 1
    • 10
    • 3
    • 1
    • 32
    • 3
    • 26
    • 3
    • 45
    • 3
    • 25
    • 3
    • 44
    • 3
    • 28
    • 3
    • 47
    • 3
    • 2
    • 1
    • 3
    • 3
    • 29
    • 3
    • 48
    • 3
    • 27
    • 3
    • 46
    • 1
    • 4
    • 1
    • 24
    • 1
    • 49
    • 1
    • 23
    • 1
    • 48
    • 1
    • 2
    • 1
    • 1
    • 1
    • 32
    • 1
    • 22
    • 0
    • 4
    • 22
    • 1
    • 54
    • 2
    • 30
    • 2
    • 29
    • 2
    • 50
    • 1
    • 10
    • 2
    • 1
    • 10
    • 12
    • 1
    • 0
    • 14
    • 1
    • 0
    • 15
    • 1
    • 0
    • 13
    • 2
    • 13
    • 2
    • 61
    • 2
    • 26
    • 2
    • 47
    • 2
    • 31
    • 1
    • 22
    • 1
    • 47
    • 2
    • 24
    • 2
    • 25
    • 2
    • 46
    • 1
    • 32
    • 14
    • 1
    • 0
    • 6
    • 1
    • 32
    • 15
    • 1
    • 0
    • 7
• Appendix B Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Alternate Map)
  • Table B.1 - Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Alternate Map) (Continued)
    • 1
    • 23
    • 1
    • 40
    • 2
    • 1
    • 1
    • 0
    • 8
    • 1
    • 13
    • 1
    • 32
    • 9
    • 1
    • 32
    • 10
    • 1
    • 10
    • 0
    • 1
    • 13
    • 1
    • 1
    • 13
    • 2
    • 1
    • 63
    • 1
    • 16
    • 1
    • 17
    • 3
    • 0
    • 3
    • 16
    • 3
    • 40
    • 3
    • 17
    • 3
    • 41
    • 2
    • 19
    • 2
    • 41
    • 2
    • 18
    • 2
    • 63
    • 2
    • 20
    • 2
    • 42
    • 1
    • 18
    • 4
    • 33
    • 4
    • 51
    • 4
    • 32
    • 1
    • 19
    • 4
    • 35
    • 4
    • 34
    • 2
    • 22
    • 2
    • 44
    • 2
    • 23
    • 2
    • 45
    • 4
    • 45
    • 4
    • 52
    • 4
    • 52
    • 4
    • 53
    • 4
    • 46
    • 4
    • 54
    • 3
    • 18
    • 3
    • 61
    • 3
    • 19
    • 3
    • 42
    • 3
    • 20
    • 3
    • 43
    • 3
    • 31
    • 1
    • 10
    • 9
    • 1
    • 5
    • 2
    • 27
    • 2
    • 48
    • 2
    • 28
    • 2
    • 49
    • 2
    • 21
    • 3
    • 54
    • 1
    • 6
    • 1
    • 10
    • 6
    • 3
    • 30
    • 3
    • 49
    • 1
    • 51
    • 3
    • 7
    • 1
    • 50
    • 3
    • 6
    • 3
    • 53
    • 5
    • 2
    • 51
    • 3
    • 8
    • 3
    • 3
    • 1
    • 1
    • 6
    • 1
    • 26
    • 8
    • 1
    • 26
    • 5
    • 1
    • 15
    • 1
    • 10
    • 5
    • 1
    • 56
    • 3
    • 24
    • 1
    • 26
    • 3
    • 1
    • 1
    • 1
    • 1
    • 26
    • 7
    • 2
    • 2
    • 1
    • 41
    • 4
    • 47
    • 4
    • 50
    • 0
    • 4
    • 48
    • 4
    • 50
    • 1
    • 4
    • 49
    • 1
    • 1
    • 14
    • 1
    • 0
    • 3
    • 1
    • 0
    • 0
    • 1
    • 0
    • 1
    • 1
    • 0
    • 1
    • 1
    • 1
    • 0
    • 5
    • 4
    • 27
    • 4
    • 41
    • 1
    • 0
    • 2
    • 1
    • 10
    • 1
    • 32
    • 8
    • 1
    • 32
    • 2
    • 1
    • 26
    • 6
    • 1
    • 61
    • 3
    • 15
    • 3
    • 57
    • 1
    • 10
    • 1
    • 4
    • 29
    • 4
    • 28
    • 4
    • 42
    • 3
    • 33
    • 1
    • 22
    • 3
    • 56
    • 3
    • 35
    • 3
    • 34
    • 1
    • 37
    • 3
    • 51
    • 3
    • 4
    • 1
    • 12
    • 3
    • 36
    • 3
    • 39
    • 3
    • 38
    • 3
    • 37
    • 1
    • 1
    • 0
    • 1
    • 0
    • 4
    • 1
    • 20
    • 4
    • 56
    • 4
    • 55
    • 4
    • 59
    • 4
    • 57
    • 4
    • 58
    • 1
    • 32
    • 4
    • 1
    • 1
    • 8
    • 1
    • 1
    • 9
    • 1
    • 1
    • 10
    • 1
    • 1
    • 11
    • 1
    • 1
    • 12
    • 1
    • 10
    • 8
    • 1
    • 0
    • 9
    • 2
    • 56
    • 1
    • 26
    • 2
    • 2
    • 54
    • 1
    • 32
    • 3
    • 2
    • 15
    • 2
    • 40
    • 1
    • 26
    • 1
    • 2
    • 14
    • 2
    • 52
    • 1
    • 14
    • 4
    • 37
    • 4
    • 60
    • 4
    • 36
    • 4
    • 39
    • 4
    • 61
    • 4
    • 38
    • 1
    • 0
    • 11
    • 1
    • 0
    • 12
    • 1
    • 26
    • 9
    • 3
    • 12
    • 3
    • 58
    • 1
    • 43
    • 2
    • 4
    • 1
    • 32
    • 11
    • 1
    • 42
    • 2
    • 3
    • 1
    • 13
    • 0
    • 3
    • 55
    • 3
    • 13
    • 3
    • 59
    • 3
    • 14
    • 3
    • 60
    • 1
    • 1
    • 15
    • 1
    • 10
    • 4
    • 3
    • 53
    • 0
    • 2
    • 58
    • 1
    • 45
    • 2
    • 6
    • 3
    • 52
    • 1
    • 28
    • 1
    • 62
    • 1
    • 34
    • 1
    • 35
    • 1
    • 36
    • 1
    • 58
    • 1
    • 59
    • 1
    • 60
    • 1
    • 29
    • 1
    • 10
    • 14
    • 1
    • 7
    • 1
    • 8
    • 1
    • 9
    • 1
    • 33
    • 4
    • 23
    • 4
    • 62
    • 4
    • 63
    • 4
    • 63
    • 1
    • 57
    • 2
    • 60
    • 2
    • 38
    • 2
    • 39
    • 2
    • 37
    • 1
    • 21
    • 1
    • 53
    • 1
    • 55
    • 1
    • 54
    • 1
    • 52
    • 3
    • 53
    • 1
    • 2
    • 11
    • 2
    • 35
    • 2
    • 34
    • 2
    • 36
    • 2
    • 59
    • 2
    • 55
    • 3
    • 53
    • 2
    • 1
    • 10
    • 13
    • 1
    • 10
    • 7
    • 4
    • 30
    • 4
    • 43
    • 4
    • 31
    • 4
    • 44
    • 1
    • 32
    • 7
    • 1
    • 10
    • 9
    • 1
    • 0
    • 10
    • 4
    • 25
    • 4
    • 40
    • 2
    • 57
    • 1
    • 44
    • 2
    • 5
    • 3
    • 1
    • 3
    • 22
    • 3
    • 62
    • 3
    • 23
    • 3
    • 63
    • 1
    • 26
    • 4
    • 2
    • 33
    • 1
    • 31
    • 2
    • 17
    • 2
    • 62
    • 1
    • 32
    • 0
    • 1
    • 46
    • 2
    • 16
    • 1
    • 10
    • 10
    • 1
    • 10
    • 3
    • 1
    • 32
    • 3
    • 26
    • 3
    • 45
    • 3
    • 25
    • 3
    • 44
    • 3
    • 28
    • 3
    • 47
    • 3
    • 2
    • 1
    • 3
    • 3
    • 29
    • 3
    • 48
    • 3
    • 27
    • 3
    • 46
    • 1
    • 4
    • 2
    • 32
    • 1
    • 39
    • 1
    • 49
    • 2
    • 9
    • 1
    • 48
    • 2
    • 8
    • 1
    • 32
    • 6
    • 1
    • 2
    • 2
    • 0
    • 1
    • 38
    • 1
    • 32
    • 1
    • 1
    • 26
    • 0
    • 1
    • 26
    • 3
    • 53
    • 3
    • 2
    • 53
    • 2
    • 29
    • 2
    • 50
    • 1
    • 10
    • 2
    • 2
    • 43
    • 1
    • 10
    • 12
    • 1
    • 1
    • 13
    • 1
    • 1
    • 7
    • 1
    • 1
    • 3
    • 1
    • 1
    • 4
    • 1
    • 1
    • 2
    • 1
    • 1
    • 5
    • 2
    • 13
    • 2
    • 61
    • 2
    • 26
    • 2
    • 47
    • 2
    • 31
    • 1
    • 47
    • 2
    • 7
    • 2
    • 24
    • 2
    • 25
    • 2
    • 46
    • 1
    • 32
    • 14
    • 1
    • 0
    • 6
    • 1
    • 0
    • 7
    • 1
    • 32
    • 15
    • 1
    • 32
    • 5
• Appendix C Cross Reference of Parameter Name to Drop and Register (WebPak 3000 Drives)
  • Table C.1 - Cross Reference of Parameter Name to Drop and Register (WebPak 3000 Map)
    • 2
    • 32
    • 2
    • 33
    • 2
    • 34
    • 2
    • 35
    • 2
    • 36
    • 2
    • 37
    • 2
    • 38
    • 2
    • 39
    • 2
    • 40
    • 2
    • 41
    • 2
    • 42
    • 2
    • 43
    • 2
    • 44
    • 2
    • 45
    • 2
    • 46
    • 2
    • 47
    • 2
    • 48
    • 2
    • 49
    • 2
    • 50
    • 2
    • 51
    • 2
    • 52
    • 2
    • 53
    • 2
    • 54
    • 2
    • 55
    • 2
    • 56
    • 2
    • 57
    • 2
    • 58
    • 2
    • 59
    • 2
    • 60
    • 2
    • 61
    • 2
    • 62
    • 2
    • 63
    • 3
    • 32
    • 3
    • 33
    • 3
    • 34
    • 3
    • 35
    • 3
    • 36
    • 3
    • 37
    • 3
    • 38
    • 3
    • 39
    • 3
    • 40
    • 3
    • 41
    • 3
    • 42
    • 3
    • 43
    • 3
    • 44
    • 3
    • 45
    • 3
    • 46
    • 3
    • 47
    • 3
    • 48
    • 3
    • 49
    • 3
    • 50
    • 3
    • 51
    • 3
    • 52
    • 3
    • 53
    • 3
    • 54
    • 3
    • 55
    • 3
    • 56
    • 3
    • 57
    • 3
    • 58
    • 3
    • 59
    • 3
    • 60
    • 3
    • 61
    • 3
    • 62
    • 3
    • 63
    • 2
    • 15
    • 1
    • 25
    • 1
    • 41
    • 1
    • 14
    • 1
    • 30
    • 1
    • 63
    • 2
    • 0
    • 2
    • 1
    • 2
    • 16
    • 2
    • 17
    • 1
    • 5
    • 1
    • 7
    • 2
    • 2
    • 2
    • 18
    • 1
    • 52
    • 1
    • 51
    • 2
    • 19
    • 1
    • 6
    • 2
    • 20
    • 1
    • 16
    • 1
    • 56
    • 3
    • 24
    • 2
    • 3
    • 1
    • 42
    • 2
    • 22
    • 2
    • 31
    • 1
    • 40
    • 2
    • 23
    • 1
    • 18
    • 2
    • 24
    • 2
    • 4
    • 2
    • 25
    • 1
    • 11
    • 1
    • 61
    • 2
    • 26
    • 2
    • 28
    • 1
    • 24
    • 1
    • 38
    • 2
    • 5
    • 1
    • 13
    • 2
    • 28
    • 1
    • 21
    • 2
    • 31
    • 2
    • 29
    • 2
    • 6
    • 2
    • 30
    • 3
    • 0
    • 3
    • 1
    • 3
    • 2
    • 3
    • 3
    • 3
    • 4
    • 1
    • 56
    • 1
    • 15
    • 3
    • 5
    • 3
    • 6
    • 1
    • 17
    • 3
    • 7
    • 1
    • 44
    • 1
    • 43
    • 1
    • 46
    • 3
    • 8
    • 1
    • 29
    • 1
    • 62
    • 1
    • 34
    • 1
    • 35
    • 1
    • 36
    • 1
    • 58
    • 1
    • 59
    • 1
    • 60
    • 3
    • 9
    • 1
    • 8
    • 1
    • 9
    • 1
    • 10
    • 1
    • 33
    • 3
    • 7
    • 3
    • 8
    • 1
    • 22
    • 1
    • 23
    • 1
    • 28
    • 3
    • 10
    • 3
    • 11
    • 3
    • 12
    • 3
    • 13
    • 3
    • 14
    • 3
    • 15
    • 1
    • 39
    • 3
    • 9
    • 1
    • 45
    • 3
    • 10
    • 1
    • 31
    • 3
    • 16
    • 1
    • 47
    • 1
    • 32
    • 3
    • 11
    • 1
    • 3
    • 3
    • 12
    • 1
    • 4
    • 1
    • 50
    • 1
    • 49
    • 1
    • 2
    • 3
    • 17
    • 3
    • 18
    • 3
    • 19
    • 3
    • 20
    • 3
    • 21
    • 3
    • 22
    • 3
    • 23
    • 1
    • 0
    • 1
    • 1
    • 1
    • 27
    • 1
    • 57
    • 2
    • 24
    • 1
    • 37
    • 2
    • 25
    • 2
    • 26
    • 1
    • 54
    • 1
    • 53
    • 2
    • 27
    • 2
    • 28
    • 3
    • 13
    • 1
    • 55
    • 1
    • 19
    • 3
    • 14
    • 1
    • 20
    • 2
    • 29
    • 1
    • 48
    • 2
    • 30
    • A
    • B
    • C
    • D
    • E
    • F
    • H
    • I
    • J
    • L
    • M
    • N
    • O
    • P
    • R
    • S
    • T
    • U
    • W
• DIF Documentation Improvement Form