FARGO electronic HDP600-LC CR100 - Manual (Page 427)

RESTRICTED USE ONLY Fargo Electronics, Inc.
HDP600 High Definition Card Printer/Encoder User Guide (Rev. 2.5) 16-4
Lam Memory Error, 4-8
Lam Pass Thru Error, 4-8
Lamination, 4-36, 15-10
Lamination Arm, 8-9, 8-10
Lamination Sensor Calibration, 4-95
Laminator Controls, 2-26
LAN (Local Area Network), 15-10
Landscape, 15-11
LCD (Liquid Crystal Display), 15-11
LCD and Softkey Control Pad, 2-16, 2-17, 2-18, 2-19, 2-
20
LCD Display, 2-14, 2-16, 2-19, 7-66
LCD Display Messages, 4-2, 4-3, 4-4
LCD Firmware, 12-7
LCD Menu, 11-1
LCD Menu and Selecting an Option, 11-1
LCD On-Line Menu Navigation, 11-1
LED (Light Emitting Diode), 15-11
LED Light, 2-14, 2-19
less heat, 7-44
less saturated resin images, 7-44
LoCo (Low Coercivity), 15-11
Low Coercivity, 7-62
lower transfer temperature, 7-4
LPT Port (Line Printer Port), 15-11
M
Mag encoding, 15-11
Mag stripe, 15-11
Mag Track, 15-11
Mag Verify, 15-11
magnetic card analyzer, 11-24
Magnetic Encoder, 4-46
Magnetic Encoding tab, 7-59
, 4-43
Magnetic Stripe Encoding Modules, 7-60
Magnetic Stripe encoding process, 7-59
Magnetic Stripe reader, 4-43
Magnetic Stripe verification, 7-66
Magnetic TOF, 11-24, 11-25, 11-26
Magnetic TOF setting, 11-24
Magnetic Track data, 7-69
Magnetic Track Options, 7-64
Magnetic Track Selection, 7-62, 7-63
Magnetic Track Selection option, 7-63
Magnetics encoder not installed., 4-5
Main Firmware, 12-4, 12-6
Main Firmware/LCD Firmware, 12-4
Main Print Board, 10-1
Manual Eject Each Error option, 7-66
matte-finished cards, 7-4
Maximum Accepted Card Length Range, 2-9
Maximum Accepted Card Width Range, 2-9
maximum value, 7-48
MB (Megabyte), 15-12
Measuring area positioned on card, 7-56
Media, 15-11
Memory, 15-12
Memory, 2-10
Menu, 15-12
MENU button, 11-1
Menu option, 2-17
MENU, Print Test Image and Gray/Align YMC, 11-10,
11-19
MENU, Setup Printer and Encoder Settings, 11-23
mistakenly-verified card, 7-66
Monochrome, 15-12
Monochrome Dye-Sub (B), 4-95
Monochrome Resin (K), 4-95
more heat, 7-44
Multi-Language Extension (MLE), 7-65
Multiple Card Feed Error, 4-3
multiple messages, 2-20
N
Network, 15-12
New Temperature Setting,
2-26
O
Oersted (Oe), 15-12
Off, 2-19
Offset, 15-12
On LED, 4-94
Operating Temperature, 2-10
O-Ring, 15-12
OS (Operating System), 15-12
Output, 15-12
Output hopper, 15-12
Output Hopper Card Capacity, 2-10
Overlaminate, 2-27, 15-13
Overlaminate Design, 2-28
Overlaminate Options (HDP600-LC only), 2-10
Overlay, 15-12
Oversized Cards, 15-13
P
Packing the Printer, 9-11
Parallel, 15-13
Parallel Interface Port, 2-15
Parallel Port, 15-13
Pass Count, 4-20, 11-31
Pause button, 2-19
Pause/Resume button, 4-94, 4-96
PC (Personal Computer), 15-13
PCB (Printed Circuit Board), 15-13
Peel, 15-13
Peel-Off, 15-13
Peripheral, 15-13
permanent circuit memory, 10-1
PET, 15-14
Photo, 7-32
Pinch Roller, 15-14
Pixel, 15-14
, 4-77
Platen, 15-14
Platen Rollers, 8-9, 8-10
Please clean your printer., 4-4
Polyester Patch Overlaminate, 2-27
PolyGuard Overlaminate, 2-27, 2-28, 15-14