Yokogawa GD40 Gas Density Detector - Manual (Page 59)

<5. DENSITY / PARAMETER SETTING>
5-4
IM 11T3E1-01E
5.1.3 Setting Parameters at Setting Level
Press the [*] key and enter the password (XXX) to gain access to this level (see Figure 5.4 for key
operation).
Table 5.3 Setting Parameters at Setting Level
Mode/Setting parameter Display
Data to be Set
(or Conditions)
Remarks
Analog output setting
Output 1
Set a parameter to be output
Set the zero and span points
Physical density
Compensated density
Specific gravity
Calorific value
Molecular weight
Concentration
Output 2 (same as output 1)
*RANGE
*OUT1
*DENS
*C_DNS
*SP_GR
*CALRY
*MOL
*CONCT
*TEMP
*PRESS
*Z_DNS,*S_DNS
*Z_CP.D,*S_CP.D
*Z_SPC,*S_SPC
*Z_CAL,*S_CAL
*Z_MOL,*S_MOL
*Z_CON,*S_CON
*OUT2
Physical density
Compensated density
Specific gravity
Calorific value
Molecular weight
Concentration
Gas temperature
Gas pressure
00.0000 to 60.0000 kg/m 3
0.00000 to 4.00000 lb/ft 3
0.0000 to 6.0000 kg/m 3
0.00000 to 0.40000 lb/ft 3
0.0000 to 5.0000
000.000 to 133.000 MJ/m 3
0.0000 to 3.5000 kBTU/ft 3
000.00 to 140.00
000.0 to 100.0
See Figure 5.4 for key operation.
No setting is required if the parameter
is temperature or pressure.
Setting calibration data
Zero-point density
Span-point density
Output hold value during cali-
bration
Setting of preset value
(Only if the preceding param-
eter is set to 2 (preset value))
*CAL.DT
*Z_DNS
*S_DNS
*C_HLD
*PR.SET
0.0000 to 6.0000 kg/m 3
0.00000 to 0.40000 lb/ft 3
0.0000 to 6.0000 kg/m 3
0.00000 to 0.40000 lb/ft 3
· Disable: 0
· Enable (value
immediately before) : 1
· Enable (preset value) : 2
-10.0 to 110.0
See Figure 8.2 for key operation.
Alarm-point setting
Select a parameter for which an
alarm is set
Physical density
Compensated density
Specific gravity
Calorific value
Molecular weight
Concentration
Set the high/low limits
Physical density
Compensated density
Specific gravity
Calorific value
Molecular weight
Concentration
*ALARM
*DENS
*C_DNS
*SP_GR
*CALRY
*MOL
*CONCT
*L_DNS,*H_DNS
*L_CP.D,*H_CP.D
*L_SPC,*H_SPC
*L_CAL,*H_CAL
*L_MOL,*H_MOL
*L_CON,*H_CON
00.0000 to 60.0000 kg/m 3
0.00000 to 4.00000 lb/ft 3
0.0000 to 6.0000 kg/m 3
0.00000 to 0.400000 lb/ft 3
0.0000 to 5.0000
000.000 to 133.000 MJ/m 3
0.0000 to 3.5000 kBTU/ft 3
000.00 to 140.00
000.0 to 100.0
See Figure 5.5 for key operation.