Lenze EVS9332xS - Manual (Page 246)

Configuration
Code table
8
8.4
l
8.4−5 EDSVS9332S EN 6.0−07/2013
IMPORTANT Possible settings Code
Selection Lenze Designation No.
C0051 MCTRL−NACT g −30000 {1 rpm} 30000 Actual speed
C0052 MCTRL−UMOT g 0 {1 V} 800 Motor voltage
C0053 UG−VOLTAGE g 0 {1 V} 900 DC−bus voltage
C0054 IMOT g 0.0 {0.1 A} 300.0 Current motor current I
mot
MCTRLfunction block
l Read only
l MCTRL−IACT = 100 % = C0022
C0056 MCTRL−MSET2 g −100.00 {0.01 %} 100.00 MCTRL−MSET2 (Mset)
Torque setpoint (n−controller output)
C0057 MAX TORQUE g 0 {1 Nm} 500 Maximum torque
Maximum possible torque of the drive
configuration
l Depending on C0022, C0086
C0058 ROTOR DIFF −90.0 −180.0 {0.1 °} 179.9 Rotor displacement angle of motor (offset
angle)
Zero phase of the rotor for synchronous
motors (C0095).
If a resolver is selected in C0025 or C0490,
C0058 is set to −90°.
l Lenze motor with resolver: C0058 = −90°
l Lenze motor with absolute value encoder:
C0058 = 0°
C0059 MOT POLE NO. g 1 {1} 50 Number of motor pole pairs
C0060 ROTOR POS g 0 {1} 2048 Motor rotor position
l 1 revolution = 2048 inc
C0061 HEATSINK
TEMP
g 0 {1 °C} 100 Heatsink temperature
C0063 MOT TEMP g 0 {1 °C} 200 Motor temperature
C0064 UTILIZATION g 0 {1 %} 150 Device utilisation I × t of the last 180 s
l C0064 >100 % releases trip OC5
l Trip reset is only possible if C0064 < 95 %
C0066 MOTOR LOAD g 0 {1 %} 250 I 2 × t utilisation of the motor
C0067 ACT TRIP g All fault
messages
à Selection list 10 Trip error message
Current fault message
C0070 VP SPEED CTRL à 0.0 {0.5} 255.0 V
pn
speed controller
à Depending on C0086
l Change of C0086 resets value to the
assigned Lenze setting
C0071 TN SPEED CTRL à 1.0 {0.5 ms} 600.0 T
nn
speed controller
At >512 ms the function is deactivated
à Depending on C0086
l Change of C0086 resets value to the
assigned Lenze setting
C0072 TD SPEED CTRL 0.0 0.0 {0.1 ms} 32.0 T
dn
speed controller
C0075 VP CURR CTRL 0.35 0.00 {0.01} 15.99 V
pi
current controller
l Depending on C0086
l Change of C0086 resets value to the
assigned Lenze setting
C0076 TN CURR CTRL 1.8 0.5 {0.1 ms} 2000.0 T
ni
current controller
At 2000 ms the function is deactivated
l Depending on C0086
l Change of C0086 resets value to the
assigned Lenze setting
C0077 VP FIELD CTRL 0.25 0.00 {0.01} 15.99 V
pF
field controller
C0078 TN FIELD CTRL 15.0 1.0 {0.5 ms} 8000.0 T
nF
field controller
At 8000 ms the function is deactivated