Verilink XEL XSP-100 SHARK IAP (9SA-USRS-9.0R1.02) Product Manual - Manual (Page 178)

Chapter 6: Using the Command Line Interface (CLI)
Chapter 6-62 XEL P/N & Release 9SA-USRS-9.0R1.02 SHARK™ IAD User’s Guide
(XCON-IF wan1 src-time-slot-15 dst-module)>>set rtr
(XCON-IF wan1 src-time-slot-15 dst-module)>>dst-time-slot
(XCON-IF wan1 src-time-slot-15 dst-time-slot)>>set 15
(XCON-IF wan1 src-time-slot-15 dst-time-slot)>>wan1 src-time-slot-16 dst-module
(XCON-IF wan1 src-time-slot-16 dst-module)>>set rtr
(XCON-IF wan1 src-time-slot-16 dst-module)>>dst-time-slot
(XCON-IF wan1 src-time-slot-16 dst-time-slot)>>set 16
(XCON-IF wan1 src-time-slot-16 dst-time-slot)>>up
(XCON-IF)>>
5. The following program LAN2 slot as the destination for this cross connect group. These
commands route 4 channels from WAN slot 1 to the destination, which is the module in
LAN2 slot DS0s 1 – 4
(XCON-IF)>>wan1
(XCON-IF wan1)>>src-time-slot-13 dst-module
(XCON-IF wan1 src-time-slot-13 dst-module)>>set lan2
(XCON-IF wan1 src-time-slot-13 dst-module)>> set dst-time-slot
(XCON-IF wan1 src-time-slot-13 dst-time-slot)>>set 1
(XCON-IF wan1 src-time-slot-13 dst-time-slot)>>wan1 src-time-slot-6 dst-module
(XCON-IF wan1 src-time-slot-6 dst-module)>>set lan2
(XCON-IF wan1 src-time-slot-6 dst-module)>>set dst-time-slot
(XCON-IF wan1 src-time-slot-6 dst-time-slot)>>set 2
(XCON-IF wan1 src-time-slot-6 dst-time-slot)>>wan1 src-time-slot-9 dst-module
(XCON-IF wan1 src-time-slot-9 dst-module)>>set lan2
(XCON-IF wan1 src-time-slot-9 dst-module)>> set dst-time-slot
(XCON-IF wan1 src-time-slot-9 dst-time-slot)>>set 3
(XCON-IF wan1 src-time-slot-9 dst-time-slot)>>wan1 src-time-slot-1 dst-module
(XCON-IF wan1 src-time-slot-1 dst-module)>>set lan2
(XCON-IF wan1 src-time-slot-1 dst-module)>> set dst-time-slot
(XCON-IF wan1 src-time-slot-1 dst-time-slot)>>set 4
(XCON-IF wan1 src-time-slot-1 dst-time-slot)>> up
(XCON-IF)>>
6. The following program LAN1 slot as the destination for this cross connect group. These
commands route 4 channels from WAN slot 1 with DS0s 21 -24 to the destination, which
is the module in LAN1 slot DS0s 5 – 8
(XCON-IF)>>wan1
(XCON-IF wan1)>>src-time-slot-21 dst-module
(XCON-IF wan1 src-time-slot-21 dst-module)>>set lan1
(XCON-IF wan1 src-time-slot-21 dst-module)>>dst-time-slot
(XCON-IF wan1 src-time-slot-21 dst-time-slot)>>set 5
(XCON-IF wan1 src-time-slot-21 dst-time-slot)>>wan1 src-time-slot-22 dst-module
(XCON-IF wan1 src-time-slot-22 dst-module)>>set lan1
(XCON-IF wan1 src-time-slot-22 dst-module)>>dst-time slot
(XCON-IF wan1 src-time-slot-22 dst-time-slot)>>set 6
(XCON-IF wan1 src-time-slot-22 dst-time-slot)>>wan1 src-time-slot-23 dst-module
(XCON-IF wan1 src-time-slot-23 dst-module)>>set lan1
(XCON-IF wan1 src-time-slot-23 dst-module)>>dst time-slot
(XCON-IF wan1 src-time-slot-23 dst-time-slot)>>set 7
(XCON-IF wan1 src-time-slot-23 dst-time-slot)>>wan1 src-time-slot-24 dst-module
(XCON-IF wan1 src-time-slot-24 dst-module)>>set lam1
(XCON-IF wan1 src-time-slot-24 dst-module)>>dst-time-slot
(XCON-IF wan1 src-time-slot-24 dst-time-slot)>>set 8
(XCON-IF wan1 src-time-slot-24 dst-time-slot)>> up
(XCON-IF)>>