A1-2, Table a1-1. drive parameters - continued – Yaskawa V7 Drives User Manual
Page 122
A1-2
PARA-
SETTING RANGE
SETTING
FACTORY
USER
PARA.
METER
NAME
(AND UNITS)
INCREMENT
SETTING
SETTING
REF.
n018
Accel/Decel Time
0:
0.1
1 (sec)
0
5.2
Setting Unit
1:
0.01
n019
Acceleration Time 1 (Note 4)
0.00 to 600.0
0.01 (sec)
n020
Deceleration Time 1 (Note 4)
or
or
5.2
n021
Acceleration Time 2 (Note 4)
0.0 to 6000
0.1 (sec)
10.0
n022
Deceleration Time 2 (Note 4)
(Dependent on n018 setting)
0:
No S-curve
n023
S-curve Selection
1:
0.2 second
1
0
5.3
2:
0.5 second
3:
1.0 second
n024
Frequency Reference 1 (Note 4)
6.00
n025
Frequency Reference 2 (Note 4)
0.00
n026
Frequency Reference 3 (Note 4)
0.01 (Hz)
0.00
n027
Frequency Reference 4 (Note 4)
0.00 to 400.00
(< 100 Hz)
0.00
n028
Frequency Reference 5 (Note 4)
or
0.00
5.11
n029
Frequency Reference 6 (Note 4)
0.1 (Hz)
0.00
n030
Frequency Reference 7 (Note 4)
(>= 100 Hz)
0.00
n031
Frequency Reference 8 (Note 4)
0.00
n032
Jog Frequency Reference (Note 4)
6.00
5.12
n033
Frequency Reference Upper
0. to 110
1(%)
100
Limit
5.9
n034
Frequency Reference Lower
0. to 110
1(%)
0
Limit
0:
0.01 Hz (less than 100 Hz) / 0.1 Hz
n035
Digital Operator
1:
0.1%
1
0
5.30
Display Mode
2 - 39: rpm
40 - 3999: custom
0.1 to 49.5
n036
Motor Rated Current
(Up to 150% of drive rated current)
0.1 (A)
(Note 1)
5.25
0:
Short term rating
n037
Electronic Thermal Overload
1:
Standard rating
1
0
Protection (for OL1 fault)
2:
Disabled
5.25
n038
Electronic Thermal Overload
1 to 60
1 (min)
8
Protection Time Constant
0:
Operates only when drive is running
n039
Cooling Fan Operation
(continues operation for 1 minute after
1
0
Selection
drive is stopped)
1:
Operates with power applied to drive
n040
Motor Rotation
0:
Rotate C.C.W.
1
0
1:
Rotate C.W. (or opposite direction)
n041
Acceleration Time 3
0.00 to 600.00
0.01 (sec)
(Note 4)
n042
Deceleration Time 3
or
or
5.2
(Note 4)
n043
Acceleration Time 4
0.0 to 6000.0
0.1 (sec)
10.0
(Note 4)
n044
Deceleration Time 4
(Dependent on n018 setting)
(Note 4)
0:
Fwd / Rev command (3 wire control)
n050
Multi-function Input
[can only be set in n052]
1
1
Selection 1 (Terminal S1)
1:
Forward run (2 wire control)
(1)
2:
Reverse run (2 wire control)
3:
External Fault (N.O.)
n051
Multi-function Input
4:
External Fault (N.C.)
1
2
5.18
Selection 2 (Terminal S2)
5:
Fault Reset
(2)
6:
Multi-step speed ref. cmd. A
n052
Multi-function Input
7:
Multi-step speed ref. cmd. B
1
3
Selection 3 (Terminal S3)
8:
Multi-step speed ref. cmd. C
(0)
Table A1-1. Drive Parameters - Continued