Yaskawa iQpump Manual Supplement - Manual (Page 56)

56 YASKAWA TM.iQp.10 Technical Manual Supplement
Preset Reference
d1-01

0280
Set-point Reference 1
Set-point 1 Digital preset setpoint reference 1. Used when b1-01 = 0 and when in
“hand” mode. Setting units are affected by P1-02.
1 ~ P1-03
Value
0.00 to
P1-02
Value
<0034>
0.00 Programming
d1-02

0281
Set-point Reference 2
Set-point 2
Digital preset setpoint reference 2. Selected via multi-function input
terminals. Setting units are affected by P1-02.
Parameter d1-02 is also the Zone 1 PI reference when b5-01 = 2.
<0034>
0.00 Programming
d1-03

0282
Set-point Reference 3
Set-point 3
Digital preset setpoint reference 3. Selected via multi-function input
terminals. Setting units are affected by P1-02.
Parameter d1-03 is also the Zone 2 PI reference when b5-01 = 2.
<0034>
0.00 Programming
d1-04

0283
Set-point Reference 4
Set-point 4
Digital preset setpoint reference 4. Selected via multi-function input
terminals. Setting units are affected by P1-02.
Parameter d1-04 is also the Zone 1 and 2 PI reference when b5-01 = 2.
<0034>
0.00 Programming
d1-17

0292
Jog Frequency Reference
Jog Reference
Jog reference used when a jog is selected via the LCD operator keypad.
This parameter is not available with the HOA operator. Setting units are
affected by o1-03.
0.00 Programming
 Denotes that parameter can be changed when the drive is running.
Reference Limits
d2-01 0289
Frequency Reference
Upper Limit
Ref Upper Limit Determines maximum speed command, set as a percentage of parameter
E1-04. If speed command is above this value, actual drive speed will be
limited to this value. This parameter applies to all speed command sources.
0.0 ~
110.0 %
100.0 % Programming
d2-02 028A
Frequency Reference
Lower Limit
Ref Lower Limit Determines minimum speed command, set as a percentage of parameter
E1-04. If speed command is below this value, actual drive speed will be set
to this value. This parameter applies to all speed command sources.
0.0 ~
110.0 %
0.0 % Programming
d2-03 0293
Master Speed Reference
Lower Limit
Ref1 Lower Limit
Determines the minimum speed command, set as a percentage of
parameter E1-04. If speed command is below this value, actual drive speed
will be set to this value. This parameter only applies
to analog inputs A1 and A2.
0.0 ~
110.0 %
0.0 % Programming
Jump Frequencies
d3-01 0294
Jump Frequency 1
Jump Freq 1
These parameters allow programming of up to three prohibited frequency
points for eliminating problems with resonant vibration of the motor/
machine. This feature does not actually eliminate the selected frequency
values, but will accelerate and decelerate the motor through the prohibited
bandwidth.
0.0 ~
200.0 Hz
0.0 Hz Programming
d3-02 0295
Jump Frequency 2
Jump Freq 2
0.0 Hz Programming
d3-03 0296
Jump Frequency 3
Jump Freq 3
0.0 Hz Programming
d3-04 0297
Jump Frequency Width
Jump Bandwidth
This parameter determines the width of the deadband around each selected
prohibited frequency point. A setting of “1.0” will result in a deadband of
+/- 1.0 Hz.
0.0 ~
20.0 Hz
1.0 Hz Programming
V/f Pattern
E1-01 0300
Input Voltage Setting
Input Voltage
Set to the nominal voltage of the incoming line.
155 ~
255.0
(240V)
310 to
510.0
(480V)
240 V
480 V
Programming
E1-03 0302
V/f Pattern Selection
V/f Selection
0: 50 Hz
1: 60 Hz Saturation
2: 50 Hz Saturation
3: 72 Hz
4: 50 Hz VT1
5: 50 Hz VT2
6: 60 Hz VT1
7: 60 Hz VT2
8: 50 Hz HST1
9: 50 Hz HST2
A: 60 Hz HST1
B: 60 Hz HST2
C: 90 Hz
D: 120 Hz
F: Custom V/F
FF: Custom w/o limit
0 ~ FF F Programming
Parameter
No.
Addr.
Hex
Parameter Name
Digital Operator
Display
Description
Setting
Range
Factory
Setting
Menu
Location